Search results

This study aims to enhance merging of additive manufacturing (AM) techniques with powder injection molding (PIM). In this way, the prototypes could be 3D-printed and mass production implemented using PIM. Thus, the surface properties and mechanical performance of parts produced using powder/polymer binder feedstocks [material extrusion (MEX) and PIM] were investigated and compared with powder manufacturing based on direct metal laser sintering (DMLS).

PIM parts were manufactured from 17-4PH stainless steel PIM-quality powder and powder intended for powder bed fusion compounded with a recently developed environmentally benign binder. Rheological data obtained at the relevant temperatures were used to set up the process parameters of injection molding. The tensile and yield strengths as well as the strain at break were determined for PIM sintered parts and compared to those produced using MEX and DMLS. Surface properties were evaluated through a 3D scanner and analyzed with advanced statistical tools.

Advanced statistical analyses of the surface properties showed the proximity between the surfaces created via PIM and MEX. The tensile and yield strengths, as well as the strain at break, suggested that DMLS provides sintered samples with the highest strength and ductility; however, PIM parts made from environmentally benign feedstock may successfully compete with this manufacturing route.

This study addresses the issues connected to the merging of two environmentally efficient processing routes. The literature survey included has shown that there is so far no study comparing AM and PIM techniques systematically on the fixed part shape and dimensions using advanced statistical tools to derive the proximity of the investigated processing routes.

The aim of this paper is presenting a new application of material obtained from the acrylonitrile butadiene styrene (ABS) recycling process from electronic equipment housings. Elements of computer monitors were used to prepare re-granulate, which in turn was used to manufacture a filament for fused filament fabrication (FFF) additive manufacturing technology.

The geometry of test samples (i.e. dumbbell and bar) was obtained in accordance with the PN-EN standards. Samples made with the FFF technology were used to determine selected mechanical properties and to compare the results obtained with the properties of ABS re-granulate mould pieces made with the injection moulding technology. The GATE device manufactured by 3Novatica was used to make the prototypes with the FFF technology. Processing parameters were tested with the use of an Aflow extrusion plastometer manufactured by Zwick/Roell and other original testing facilities. Tests of mechanical properties were performed with a Z030 universal testing machine, a HIT 50P pendulum impact tester and a Z3106 hardness tester manufactured by Zwick/Roell.

The paper presents results of tests performed on a filament obtained from the ABS re-granulate and indicates characteristic processing properties of that material. The properties of the new secondary material were compared with the available original ABS materials that are commonly used in the additive technology of manufacturing geometrical objects. The study also presents selected results of tests of functional properties of ABS products made in the FFF technology.

The test results allowed authors to assess the possibility of a secondary application of used elements of electronic equipment housings in the FFF technology and to compare the strength properties of products obtained with similar products made with the standard injection moulding technology.

This study aims to examine factors that determine the adoption of additive manufacturing by small- and medium-sized industries. It provides insights with regard to benefits, challenges and business factors that influence small- and medium-sized industries when adopting this technology. The study also aims to expand the domain of additive manufacturing by including a broader range of challenges and benefits of additive manufacturing in literature.

Using data collected from 175 small- and medium-sized industries, the study has examined through Mann–Whitney test to understand the difference between owners and design engineers on additive manufacturing technology adoption in small- and medium-sized companies.

This study suggests contribution to academic discussion by providing associated factors that have significant impact on the adoption of additive manufacturing technology. Related advantages of additive manufacturing are reduction in inventory cost, lowering the wastage in production and customization of products. The study also indicates that factors such as cost of machinery, higher level of cost in integrating metal components have a negative impact on the adoption of this technology in small- and medium-sized industries.

Because of the chosen research approach, the research results may lack generalizability. Therefore, researchers are encouraged to test the proposed propositions further in the field of challenges and growth in other areas of application of additive manufacturing, for instance, medical sciences, fabric and aerospace.

The study provides important implications that are of interest for both research and practitioners, related to technology management in small- and medium-sized industries, e.g. foundry and machining industries.

This work/study fulfills an identified need of the small- and medium-sized companies in adopting new technologies and contribute to their growth by understanding the need to accept and implement technology.

This paper fulfills an identified need to study how small- and medium-scale companies accept new technologies and factors associated with implementation in the manufacturing process of the organization.

This study aims to provide a comprehensive overview of the current state of the art in powder bed fusion (PBF) techniques for additive manufacturing of multiple materials. It reviews the emerging technologies in PBF multimaterial printing and summarizes the latest simulation approaches for modeling them. The topic of “multimaterial PBF techniques” is still very new, undeveloped, and of interest to academia and industry on many levels.

This is a review paper. The study approach was to carefully search for and investigate notable works and peer-reviewed publications concerning multimaterial three-dimensional printing using PBF techniques. The current methodologies, as well as their advantages and disadvantages, are cross-compared through a systematic review.

The results show that the development of multimaterial PBF techniques is still in its infancy as many fundamental “research” questions have yet to be addressed before production. Experimentation has many limitations and is costly; therefore, modeling and simulation can be very helpful and is, of course, possible; however, it is heavily dependent on the material data and computational power, so it needs further development in future studies.

This work investigates the multimaterial PBF techniques and discusses the novel printing methods with practical examples. Our literature survey revealed that the number of accounts on the predictive modeling of stresses and optimizing laser scan strategies in multimaterial PBF is low with a (very) limited range of applications. To facilitate future developments in this direction, the key information of the simulation efforts and the state-of-the-art computational models of multimaterial PBF are provided.

This paper aims to present a comprehensive review of the laser engineered net shaping (LENS) process in an attempt to provide the reader with a deep understanding of the controllable and fixed build parameters of metallic parts. The authors discuss the effect and interplay between process parameters, including: laser power, scan speed and powder feed rate. Further, the authors show the interplay between process parameters is pivotal in achieving the desired microstructure, macrostructure, geometrical accuracy and mechanical properties.

In this manuscript, the authors review current research examining the process inputs and their influences on the final product when manufacturing with the LENS process. The authors also discuss how these parameters relate to important build aspects such as melt-pool dimensions, the volume of porosity and geometry accuracy.

The authors conclude that studies have greatly enriched the understanding of the LENS build process, however, much studies remains to be done. Importantly, the authors reveal that to date there are a number of detailed theoretical models that predict the end properties of deposition, however, much more study is necessary to allow for reasonable prediction of the build process for standard industrial parts, based on the synchronistic behavior of the input parameters.

This paper intends to raise questions about the possible research areas that could potentially promote the effectiveness of this LENS technology.

The purpose of this paper is to investigate the effect of remelting each layer on the homogeneity of nickel-titanium (NiTi) parts fabricated from elemental nickel and titanium powders using laser powder bed fusion (LPBF). In addition, the influence of manufacturing parameters and different melting strategies, including multiple cycles of remelting, on printability and macro defects, such as pore and crack formation, have been investigated.

An LPBF process was used to manufacture NiTi alloy from elementally blended powders and was evaluated with the use of a remelting scanning strategy to improve the homogeneity of fabricated specimens. Furthermore, both single melt and up to two remeltings were used.

The results indicate that remelting can be beneficial for density improvement as well as chemical and phase composition homogenization. Backscattered electron mode in scanning electron microscope showed a reduction in the presence of unmixed Ni and Ti elemental powders in response to increasing the number of remelts. The microhardness values of NiTi parts for the different numbers of melts studied were similar and ranged from 487 to 495 HV. Nevertheless, it was observed that measurement error decreases as the number of remelts increases, suggesting an increase in chemical and phase composition homogeneity. However, X-ray diffraction analysis revealed the presence of multiple phases regardless of the number of melt runs.

For the first time, to the best of the authors’ knowledge, elementally blended NiTi powders were fabricated via LPBF using remelting scanning strategies.

Particles bed binding by selective cement activation (SCA) method is a computer-aided manufacturing (CAM) technique used to produce cementitious elements. A computer-aided design file is sliced to generate G-codes before printing. This paper aims to study the effect of key input parameters for slicer software on the final properties of printed products.

The one factor at a time (OFAT) methodology is used to investigate the impact of selected parameters on the final properties of printed specimens, and the causes for the variations in outcomes of each variable are discussed.

Finer aggregates can generate a more compact layer, resulting in a denser product with higher strength. Fluid pressure is directly determined by voxel rate (r_V); however, high pressures enable better fluid penetration control for fortified products; for extreme r_Vs, residual voids in the interfaces between successive layers and single-line primitives impair mechanical strength. It was understood that printhead movement along the orientation of the parts in the powder bed improved the mechanical properties.

The design of experiment (DOE) method assesses the influence of process parameters on various input printing variables at the same time. As the resources are limited, a fractional factorial plan is carried out on a subset of a full factorial design; hence, providing physical interpretation behind changes in each factor is difficult. OFAT aids in analyzing the effect of a change in one factor on output while all other parameters are kept constant. The results assist engineers in properly considering the influence of variable variations for future DOE designs.

The purpose of this paper is to communicate a method to perform simultaneous topology optimization of component and support structures considering typical metal additive manufacturing (AM) restrictions and post-print machining requirements.

An integrated topology optimization is proposed using two density fields: one describing the design and another defining the support layout. Using a simplified AM process model, critical overhang angle restrictions are imposed on the design. Through additional load cases and constraints, sufficient stiffness against subtractive machining loads is enforced. In addition, a way to handle non-design regions in an AM setting is introduced.

The proposed approach is found to be effective in producing printable optimized geometries with adequate stiffness against machining loads. It is shown that post-machining requirements can affect optimal support structure layout.

This study uses a simplified AM process model based on geometrical characteristics. A challenge remains to integrate more detailed physical AM process models to have direct control of stress, distortion and overheating.

The presented method can accelerate and enhance the design of high performance parts for AM. The consideration of post-print aspects is expected to reduce the need for design adjustments after optimization.

The developed method is the first to combine AM printability and machining loads in a single topology optimization process. The formulation is general and can be applied to a wide range of performance and manufacturability requirements.

Introducing additive manufacturing (AM) in a multinational corporation with a global spare parts operation requires tools for a dynamic supplier selection, considering both cost and delivery performance. In the switchover to AM from conventional manufacturing, the objective of this study is to find situations and ways to improve the spare parts service to end customers.

In this explorative study, the authors develop a procedure – in collaboration with the spare parts operations managers of a case company – for dynamic operational decision-making for the selection of spare parts supply from multiple suppliers. The authors' design proposition is based on a field experiment for the procurement and delivery of 36 problematic spare parts.

The practice intervention verified the intended outcomes of increased cost and delivery performance, yielding improved customer service through a switchover to AM according to situational context. The successful operational integration of dynamic additive and static conventional supply was triggered by the generative mechanisms of highly interactive model-based supplier relationships and insignificant transaction costs.

The dynamic decision-making proposal extends the product-specific make-to-order practice to the general-purpose build-to-model that selects the mode of supply and supplier for individual spare parts at an operational level through model-based interactions with AM suppliers. The successful outcome of the experiment prompted the case company to begin the introduction of AM into the company's spare parts supply chain.

Although additive manufacturing (AM; 3D printing/3DP) is presently in its infancy, once it becomes economically viable for mass production, it would revolutionize the operation and supply chain network of traditional businesses and manufacturing industries. To this end, approaches for ensuring a smooth transition of the economy, businesses, manufacturing centers and related services are being investigated. This review paper assesses the existing literature on the impact of AM on the maritime transportation sector.

This paper provides a systematic literature review through three methodological phases: (1) a comprehensive review of the number of English language literature studies published on the topics of AM or 3DP (1970–2021); (2) a bibliometric analysis of selected keyword combinations and (3) a detailed review on the impact of AM on different sectors.

The key findings are that existing studies do not attempt to forecast shipping volume and ton-miles that can be affected by the mainstreaming of the technology. Additionally, existing literature that focuses on the impact of the technology on different shipping categories is limited to studies on container ships.

The review identifies some potential areas of research that since maritime transportation will be affected by mainstreaming AM, it will have economic, social and environmental impacts on global trade that require future assessment.