Search results

Under the widely used testing methods for fabric bending behavior, only one result for one direction can be obtained by using one fabric which is low efficient. To obtain fabric bending anisotropy, it is necessary to conduct a great many testing experiments. The purpose of this paper is to investigate a novel, efficient and visual method that can measure fabric bending anisotropy.

Fabrics are first cut into special shapes with eight strips including four directions, 0°(warp direction), 90°(weft direction), 45 and 135°(true bias), then are put onto the self-designed instrument. After that a camera is used to take picture from the right above the prism. New parameters, projection area, projection length, projection length, falling height and falling index (S, L, H and I in short) are obtained. Furthermore, standard deviation of them (SDS, SDL, SDH and SDI in short) are extracted for the characterization of bending anisotropy.

Results show that the new method has good feasibility and S, L and I can be used to express fabric bending property well. Of all the four new parameters, SDL has the highest correlation with SD of bending length, SDS the second and SDH the third. That is, SDL can characterize bending anisotropy best. Taken convenience of data acquisition and correlation into consideration, bending length L is the best parameter. Average L and SDL in four directions can be combined to express the comprehensive bending behavior of fabrics.

The new method can measure and characterize both the fabric bending property and bending anisotropy. Besides its high efficiency, it can display fabric bending or bending anisotropy visually and directly.

Microribbon with meander type based on giant magnetoimpedance (GMI) effect has become a research hot spot due to their higher sensitivity and spatial resolution. The purpose of this paper is to further optimize the line spacing to improve the performance of meanders for sensor application.

The model of GMI effect of microribbon with meander type is established. The effect of line spacing (Ls) on GMI behavior in meanders is analyzed systematically.

Comparison of theory and experiment indicates that decreasing the line spacing increases the negative mutual inductance and a consequent increase in the GMI effect. The maximum value of the GMI ratio increases from 69% to 91.8% (simulation results) and 16.9% to 51.4% (experimental results) when the line spacing is reduced from 400 to 50 µm. The contribution of line spacing versus line width to the GMI ratio of microribbon with meander type was contrasted. This behavior of the GMI ratio is dominated by the overall negative contribution of the mutual inductance.

This paper explores the effect of line spacing on the GMI ratio of meander type by comparing the simulation results with the experimental results. The superior line spacing is found in the identical sensing area. The findings will contribute to the design of high-performance micropatterned ribbon with meander-type GMI sensors and the establishment of a ribbon-based magnetic-sensitive biosensing system.

Because of the anisotropy of the process and the variability in the quality of printed parts, finite element analysis is not directly applicable to recycled materials manufactured using fused filament fabrication. The purpose of this study is to investigate the numerical-experimental mechanical behavior modeling of the recycled polymer, that is, recyclable polyethylene terephthalate (rPET), manufactured by a deposition FFF process under compressive stresses for new sustainable designs.

In all, 42 test specimens were manufactured and analyzed according to the ASTM D695-15 standards. Eight numerical analyzes were performed on a real design manufactured with rPET using Young's compression modulus from the experimental tests. Finally, eight additional experimental tests under uniaxial compression loads were performed on the real sustainable design for validating its mechanical behavior versus computational numerical tests.

As a result of the experimental tests, rPET behaves linearly until it reaches the elastic limit, along each manufacturing axis. The results of this study confirmed the design's structural safety by the load scenario and operating boundary conditions. Experimental and numerical results show a difference of 0.001–0.024 mm, allowing for the rPET to be configured as isotropic in numerical simulation software without having to modify its material modeling equations.

The results obtained are of great help to industry, designers and researchers because they validate the use of recycled rPET for the ecological production of real-sustainable products using MEX technology under compressive stress and its configuration for numerical simulations. Major design companies are now using recycled plastic materials in their high-end designs.

Validation results have been presented on test specimens and real items, comparing experimental material configuration values with numerical results. Specifically, to the best of the authors’ knowledge, no industrial or scientific work has been conducted with rPET subjected to uniaxial compression loads for characterizing experimentally and numerically the material using these results for validating a real case of a sustainable industrial product.

Confronting the unveiled sophisticated structural and physical characteristics of permanent magnets, notably the samarium–cobalt (Sm-Co) alloy, This work aims to introduce a simulation scheme that can link physics-based micromagnetics on the nanostructures and magnetostatic homogenization on the mesoscale polycrystalline structures.

The simulation scheme is arranged in a multiscale fashion. The magnetization behaviors on the nanostructures examined with various orientations are surrogated as the micromagnetic-informed hysterons. The hysteresis behavior of the mesoscale polycrystalline structures with micromagnetic-informed hysterons is then evaluated by computational magnetostatic homogenization.

The micromagnetic-informed hysterons can emulate the magnetization reversal of the parameterized Sm-Co nanostructures as the local hysteresis behavior on the mesostructures. The simulation results of the mesoscale polycrystal demonstrate that the demagnetization process starts from the grain with the largest orientation angle (a) and then propagates to the surrounding grains.

The presented scheme depicts the demand for integrating data-driven methods, as the parameters of the surrogate hysteron intrinsically depend on the nanostructure and its orientation. Further hysteron parameters that help the surrogate hysteron emulate the micromagnetic-simulated magnetization reversal should be examined.

This work provides a novel multiscale scheme for simulating the polycrystalline permanent magnets’ hysteresis while recapitulating the nanoscale mechanisms, such as the nucleation of domains, and domain wall migration and pinning. This scheme can be further extended to simulate the part-level hysteresis considering the mesoscale features.

Many additively manufactured parts suffer from reduced interlayer strength. This anisotropy is necessarily tied to the orientation during manufacture. When individual features on a part have conflicting optimal orientations, the part is unavoidably compromised. This paper aims to demonstrate a strategy in which conflicting features can be functionally separated into “co-parts” which are individually aligned in an optimal orientation, selectively reinforced with continuous fiber, printed simultaneously and, finally, assembled into a composite part with substantially improved performance.

Several candidate parts were selected for co-part decomposition. They were printed as standard fused filament fabrication plastic parts, parts reinforced with continuous fiber in one plane and co-part assemblies both with and without continuous fiber reinforcement (CFR). All parts were loaded until failure. Additionally, parts representative of common suboptimally oriented features (“unit tests”) were similarly printed and tested.

CFR delivered substantial improvement over unreinforced plastic-only parts in both standard parts and co-part assemblies, as expected. Reinforced parts held up to 2.5x the ultimate load of equivalent plastic-only parts. The co-part strategy delivered even greater improvement, particularly when also reinforced with continuous fiber. Plastic-only co-part assemblies held up to 3.2x the ultimate load of equivalent plastic only parts. Continuous fiber reinforced co-part assemblies held up to 6.4x the ultimate load of equivalent plastic-only parts. Additionally, the thought process behind general co-part design is explored and a vision of simulation-driven automated co-part implementation is discussed.

This technique is a novel way to overcome one of the most common challenges preventing the functional use of additively manufactured parts. It delivers compelling performance with continuous carbon fiber reinforcement in 3D printed parts. Further study could extend the technique to any anisotropic manufacturing method, additive or otherwise.

The malfunction variables of power stations are related to the areas of weather, physical structure, control and load behaviour. To predict temporal power failure is difficult due to their unpredictable characteristics. As high accuracy is normally required, the estimation of failures of short-term temporal prediction is highly difficult. This study presents a method for converting stochastic behaviour into a stable pattern, which can subsequently be used in a short-term estimator. For this conversion, K-means clustering is employed, followed by Long-Short-Term Memory (LSTM) and Gated Recurrent Unit (GRU) algorithms are used to perform the Short-term estimation. The environment, the operation and the generated signal factors are all simulated using mathematical models. Weather parameters and load samples have been collected as part of a data set. Monte-Carlo simulation using MATLAB programming has been used to conduct experimental estimation of failures. The estimated failures of the experiment are then compared with the actual system temporal failures and found to be in good match. Therefore, for any future power grid, there is a testbed ready to estimate the future failures.

This paper aims to introduce an alternative for modeling levitation forces between NdFeB magnets and bulks of high-temperature superconductors (HTS). The presented approach should be evaluated through two different formulations and compared with experimental results.

The T-A and H-ϕ formulations are among the most efficient approaches for modeling superconducting materials. COMSOL Multiphysics was used to apply them to magnetic levitation models and predict the forces involved.The permanent magnet movement is modeled by combining moving meshes and magnetic field identity pairs in both 2D and 3D studies.

It is shown that it is possible to use the homogenization technique for the T-A formulation in 3D models combined with mixed formulation boundaries and moving meshes to simulate the whole device’s geometry.

The case studies are limited to the formulations’ implementation and a brief assessment regarding degrees of freedom. The intent is to make the simulation straightforward rather than establish a benchmark.

The H-ϕ formulation considers the HTS bulk domain as isotropic, whereas the T-A formulation homogenization approach treats it as anisotropic. The originality of the paper lies in contrasting these different modeling approaches while incorporating the external magnetic field movement by means of the Lagrangian–Eulerian method.

Modeling of material behavior by physically or microstructure-based models helps in understanding the relationships between its properties and microstructure. However, the majority of the numerical investigations on the prediction of the deformation behavior of AA2024 alloy are limited to the use of phenomenological or empirical constitutive models, which fail to take into account the actual microscopic-level mechanisms (i.e. crystallographic slip) causing plastic deformation. In order to achieve accurate predictions, the microstructure-based constitutive models involving the underlying physical deformation mechanisms are more reliable. Therefore, the aim of this work is to predict the mechanical response of AA2024-T3 alloy subjected to uniaxial tension at different strain rates, using a dislocation density-based crystal plasticity model in conjunction with computational homogenization.

A dislocation density-based crystal plasticity (CP) model along with computational homogenization is presented here for predicting the mechanical behavior of aluminium alloy AA2024-T3 under uniaxial tension at different strain rates. A representative volume element (RVE) containing 400 grains subjected to periodic boundary conditions has been used for simulations. The effect of mesh discretization on the mechanical response is investigated by considering different meshing resolutions for the RVE. Material parameters of the CP model have been calibrated by fitting the experimental data. Along with the CP model, Johnson–Cook (JC) model is also used for examining the stress-strain behavior of the alloy at various strain rates. Validation of the predictions of CP and JC models is done with the experimental results where the CP model has more accurately captured the deformation behavior of the aluminium alloy.

The CP model is able to predict the mechanical response of AA2024-T3 alloy over a wide range of strain rates with a single set of material parameters. Furthermore, it is observed that the inhomogeneity in stress-strain fields at the grain level is linked to both the orientation of the grains as well as their interactions with one another. The flow and hardening rule parameters influencing the stress-strain curve and capturing the strain rate dependency are also identified.

Computational homogenization-based CP modeling and simulation of deformation behavior of polycrystalline alloy AA2024-T3 alloy at various strain rates is not available in the literature. Therefore, the present computational homogenization-based CP model can be used for predicting the deformation behavior of AA2024-T3 alloy more accurately at both micro and macro scales, under different strain rates.

This study presents finite element (FE) and generalized regression neural network (GRNN) approaches for modeling multiple crack growth problems and predicting crack-growth directions under the influence of multiple crack parameters.

To determine the crack-growth direction in aluminum specimens, multiple crack parameters representing some degree of crack propagation complexity, including crack length, inclination angle, offset and distance, were examined. FE method models were developed for multiple crack growth simulations. To capture the complex relationships among multiple crack-growth variables, GRNN models were developed as nonlinear regression models. Six input variables and one output variable comprising 65 training and 20 test datasets were established.

The FE model could conveniently simulate the crack-growth directions. However, several multiple crack parameters could affect the simulation accuracy. The GRNN offers a reliable method for modeling the growth of multiple cracks. Using 76% of the total dataset, the NN model attained an R2 value of 0.985.

The models are presented for static multiple crack growth problems. No material anisotropy is observed.

In practical crack-growth analyses, the NN approach provides significant benefits and savings.

The proposed GRNN model is simple to develop and accurate. Its performance was superior to that of other NN models. This model is also suitable for modeling multiple crack growths with arbitrary geometries. The proposed GRNN model demonstrates its prediction capability with a simpler learning process, thus producing efficient multiple crack growth predictions and assessments.

The objective of this paper is to quantitatively assess shear band evolution by using two-dimensional discrete element method (DEM).

The DEM model was first calibrated by retrospectively modelling existing triaxial tests. A series of DEM analyses was then conducted with the focus on the particle rotation during loading. An approach based on particle rotation was developed to precisely identify the shear band region from the surrounding. In this approach, a threshold rotation angle ω₀ was defined to distinguish the potential particles inside and outside the shear band and an index g(ω₀) was introduced to assess the discrepancy between the rotation response inside and outside shear band. The most distinct shear band region can be determined by the ω₀ corresponding to the peak g(ω₀). By using the proposed approach, the shear band development of two computational cases with different typical localised failure patterns were successfully examined by quantitatively measuring the inclination angle and thickness of shear band, as well as the microscopic quantities.

The results show that the shear band formation is stress-dependent, transiting from conjugated double shear bands to single shear band with confining stress increasing. The shear band evolution of two typical localised failure modes exhibits opposite trends with increasing strain level, both in inclination angle and thickness. Shear band featured a larger volumetric dilatancy and a lower coordination number than the surrounding. The shear band also significantly disturbs the induced anisotropy of soil.

This paper proposed an approach to quantitatively assess shear band evolution based on the result of two-dimensional DEM modelling.