Search results

The purpose of this work was to characterize NiMn₂O₄ spinel-based thermistor powder, to use it in screen printing technology to fabricate temperature sensors, to study their performance for different sintering temperatures of thermistor layer, with and without insulative cover, as well as to investigate stability of the fabricated thermistors and their applicability in water quality monitoring.

After the characterization of starting NiMn₂O₄ spinel-based thermistor powder, it was converted to thick film paste which was screen printed on alumina substrate. Thermistor layers were sintered at four different sintering temperatures: 980°C, 1050°C, 1150°C and 1290°C. An interdigitated pattern of Ag-Pd conductive layer was used to reduce the resistance. Temperature-resistance characteristics were investigated in air and water, with and without insulative cover atop the thermistor layer. Stability of the fabricated thermistors after aging at 120°C for 300 h was also examined.

Thick film NiMn₂O₄ spinel thermistors, prepared by screen printing and sintering in the temperature range 980°C–1290°C, exhibited good negative temperature coefficient (NTC) characteristics in the temperature range −30°C to 145°C, including high temperature coefficient of resistance, good stability and applicability in water.

This study explores the range of sintering temperature that can be applied for NiMn₂O₄ thermistor thick films without compromising on the temperature sensing performance in air and water, as well as stability of the thermistors after aging at elevated temperatures.

This study aims to enhance merging of additive manufacturing (AM) techniques with powder injection molding (PIM). In this way, the prototypes could be 3D-printed and mass production implemented using PIM. Thus, the surface properties and mechanical performance of parts produced using powder/polymer binder feedstocks [material extrusion (MEX) and PIM] were investigated and compared with powder manufacturing based on direct metal laser sintering (DMLS).

PIM parts were manufactured from 17-4PH stainless steel PIM-quality powder and powder intended for powder bed fusion compounded with a recently developed environmentally benign binder. Rheological data obtained at the relevant temperatures were used to set up the process parameters of injection molding. The tensile and yield strengths as well as the strain at break were determined for PIM sintered parts and compared to those produced using MEX and DMLS. Surface properties were evaluated through a 3D scanner and analyzed with advanced statistical tools.

Advanced statistical analyses of the surface properties showed the proximity between the surfaces created via PIM and MEX. The tensile and yield strengths, as well as the strain at break, suggested that DMLS provides sintered samples with the highest strength and ductility; however, PIM parts made from environmentally benign feedstock may successfully compete with this manufacturing route.

This study addresses the issues connected to the merging of two environmentally efficient processing routes. The literature survey included has shown that there is so far no study comparing AM and PIM techniques systematically on the fixed part shape and dimensions using advanced statistical tools to derive the proximity of the investigated processing routes.

The purpose of this paper is to review possibilities of implementing ceramic additive manufacturing (AM) into electronic device production, which can enable great new possibilities.

A short introduction into additive techniques is included, as well as primary characterization of structuring capabilities, dielectric performance and applicability in the electronic manufacturing process.

Ceramic stereolithography (SLA) is suitable for microchannel manufacturing, even using a relatively inexpensive system. This method is suitable for implementation into the electronic manufacturing process; however, a search for better materials is desired, especially for improved dielectric parameters, lowered sintering temperature and decreased porosity.

Relatively inexpensive ceramic SLA, which is now available, could make ceramic electronics, currently restricted to specific applications, more available.

Ceramic AM is in the beginning phase of implementation in electronic technology, and only a few reports are currently available, the most significant of which is mentioned in this paper.

Purpose – In this research, we have prepared activated carbon (AC) from the waste of banana peels (Musa acuminate L.) using potassium hydroxide (KOH) for carbon monoxide (CO) adsorption from motorcycle gas emission.

Design/Methodology/Approach – The activation was conducted using a chemical activator (KOH) at various concentrations of 1, 2, and 3 N for 1, 2, and 3 h, respectively. Characteristics of banana peels AC (BPAC) produced were analyzed using the Fourier-transform infra-red spectroscopy and scanning electron microscopy.

Findings – Results showed that KOH concentration and activation time strongly affected the CO adsorption and opening of the AC surface pore. There was an increase in the CO sorption when the KOH concentration was increased up to 3 N concentration. The highest CO adsorption from the emission occurred at 70.95% under KOH concentration of 3 N during the 3-h preparation.

Research Limitations/Implications – BPAC has been used as an adsorbent for only CO from motorcycle gas emission but not as an adsorbent for HC, NO, NO_x, or H₂S.

Practical Implications – BPAC can be used as the potential adsorbent for the removal of CO from motorcycle gas emission, and it is an environmental friendly, low cost, and easy to make adsorbent.

Originality/Value – In this study, the AC is made from biomass and is used in wastewater treatment, but limited studies are found on the removal of CO from motorcycle gas emission.

Polyurethane (PUR) foam parts are traditionally manufactured using metallic molds, an unsuitable approach for prototyping purposes. Thus, rapid tooling of disposable molds using fused filament fabrication (FFF) with polylactic acid (PLA) and glycol-modified polyethylene terephthalate (PETG) is proposed as an economical, simpler and faster solution compared to traditional metallic molds or three-dimensional (3D) printing with other difficult-to-print thermoplastics, which are prone to shrinkage and delamination (acrylonitrile butadiene styrene, polypropilene-PP) or high-cost due to both material and printing equipment expenses (PEEK, polyamides or polycarbonate-PC). The purpose of this study has been to evaluate the ease of release of PUR foam on these materials in combination with release agents to facilitate the mulding/demoulding process.

PETG, PLA and hardenable polylactic acid (PLA 3D870) have been evaluated as mold materials in combination with aqueous and solvent-based release agents within a full design of experiments by three consecutive molding/demolding cycles.

PLA 3D870 has shown the best demoldability. A mold expressly designed to manufacture a foam cushion has been printed and the prototyping has been successfully achieved. The demolding of the part has been easier using a solvent-based release agent, meanwhile the quality has been better when using a water-based one.

The combination of PLA 3D870 and FFF, along with solvent-free water-based release agents, presents a compelling low-cost and eco-friendly alternative to traditional metallic molds and other 3D printing thermoplastics. This innovative approach serves as a viable option for rapid tooling in PUR foam molding.

The electrical properties of piezoelectric vibrators have a crucial influence on the operating state of ultrasonic motors. In order to solve the problem that the current piezoelectric vibrator generates a large amount of heat during vibration to degrade its performance, which in turn affects the normal operation of ultrasonic motors, this paper prepares a novel piezoelectric vibrator and tests its maximum vibration velocity under the working condition, which is more than twice as much as that of the current commercial PZT-8.

The crystal structures of the samples were analyzed by using an X-ray diffractometer. For microstructure observation, samples were observed by scanning electron microscope (SEM). The quasi-static piezoelectric coefficient meter (ZJ-3AN) was used for piezoelectric measurement. Dielectric properties were measured by utilizing an impedance analyzer (Agilent 4294A) with a laboratory heating unit. Ferroelectric hysteresis loops were obtained using a ferroelectric analyzer (Radiant, Multiferroic 100). A Doppler laser vibrometer (Polytec PSV-300F, Germany) and a power amplifier were used for piezoelectric vibration measurements, during which the temperature rise was determined by an infrared radiation thermometer (Victor 303, China).

The ceramics exhibit enhanced piezoelectric performance at 0.1–0.4 mol% of Yb doping contents. The ceramic of 0.4 mol% Yb reaches the maximal internal bias field and presents a larger mechanical quality factor of 1,692 compared with that of 0.2 mol% Yb-doped ceramic, in spite of a slightly decreased dielectric constant of 439 pC/N, the unit of the piezoelectric constant, which is the ratio of the local charge (pC) to the frontal force (N) and electromechanical coupling coefficient of 0.63. The vibrator with this large mechanical quality factor ceramic displays a vibration velocity of up to 0.81 m/s under the constraint of 20 °C temperature rising, which is much higher than commercial high-power piezoelectric ceramics PZT-8.

The enhanced high-power properties of the piezoelectric vibrator by Yb doping may provide a potential application for the high-performance USM and offer the possibility of long-term stable operation under high power for special equipment like USM. In the subsequent phase of research, the novel PZT-based high-power piezoelectric vibrator can be utilized in the USM, and the motor's performance will be evaluated under aerospace conditions to objectively assess the reliability of the piezoelectric vibrator.

Because of the significant differences in the features and requirements of specific products and the capabilities of various additive manufacturing (AM) solutions, selecting the most appropriate AM technology can be challenging. This study aims to propose a method to solve the complex process selection in 3D printing applications, especially by creating a new multicriteria decision-making tool that takes the direct certainty of each comparison to reflect the decision-maker’s desire effectively.

The methodology proposed includes five steps: defining the AM technology selection decision criteria and constraints, extracting available AM parameters from the database, evaluating the selected AM technology parameters based on the proposed decision-making methodology, improving the accuracy of the decision by adopting newly proposed weighting scheme and selecting optimal AM technologies by integrating information gathered from the whole decision-making process.

To demonstrate the feasibility and reliability of the proposed methodology, this case study describes a detailed industrial application in rapid investment casting that applies the weightings to a tailored AM technologies and materials database to determine the most suitable AM process. The results showed that the proposed methodology could solve complicated AM process selection problems at both the design and manufacturing stages.

This research proposes a unique multicriteria decision-making solution, which employs an exclusive weightings calculation algorithm that converts the decision-maker's subjective priority of the involved criteria into comparable values. The proposed framework can reduce decision-maker's comparison duty and potentially reduce errors in the pairwise comparisons used in other decision-making methodologies.

The traditional grey relational models directly describe the behavioural characteristics of the systems based on the sample point connections. Few grey relational models can measure the dynamic periodic fluctuation rules of the objects, and most of these models do not have affinities, which results in instabilities of the relational results because of sequence translation. The paper aims to discuss these issues.

Fourier transform functions are used to fit the system behaviour curves, redefine the area difference between the curves and construct a grey relational model based on discrete Fourier transform (DFTGRA).

To verify its validity, feasibility and superiority, DFTGRA is applied to research on the correlation between macroeconomic growth and marine economic growth in China coastal areas. It is proved that DFTGRA has the superior properties of affinity, symmetry, uniqueness, etc., and wide applicability.

DFTGRA can not only be applied to equidistant and equal time sequences but also be adopted for non-equidistant and unequal time sequences. DFTGRA can measure both the global relational degree and the dynamic correlation of the variable cyclical fluctuation between sequences.

Dry eye syndrome is one of the most common reasons for eye-related discomfort which, without treatment, in some cases may even lead to corneal damage. Blinking, baseline and reflex lachrymation and drainage compromise the topical application of therapeutics demanding repeated, often hourly applications of common lubricants. In contrast, topically administered chitosan-N-acetylcysteine-based eye drops were reported to sustain on the ocular surface for more than 24 h. The thiolated biopolymer can interact with the corneal mucin layer thereby forming covalent disulphide bridges, which may contribute to extended residence times.

In this study, the tribological characteristics of four different lubricants including hyaluronic acid and chitosan-N-acetylcysteine containing commercially available eye drops were investigated. For this purpose, a representative test setup was developed, which mimics the contact between the cornea and the eyelid wiper. Gels with different elastic properties coated with a mucin layer were used as a substrate to mimic the corneal surface. Tests were conducted with a micro-tribometer, and friction values were recorded. Contact zones were characterized by X-ray photoelectron spectroscopy to investigate wear and thiol bonding on the surface.

Results revealed the lowest average coefficient of friction values for chitosan-N-acetylcysteine-based eye drops and substrate dependence of the test setup.

In this study, the authors introduced an in vitro system to test different types of eye drops so that chemical interaction with the mucin layer can be observed. These interactions change the tribological performance significantly and must be considered to have results relevant to the actual application.

In this paper, we examine the comparative advantage of Korea and China while focusing on their technology level. The three digit SITC (Standard International Trade Classification) data is classified by technology level and the revealed comparative advantage (RCA) is derived from 1992-2009 by using UN COMTRADE data. For careful interpretation of the comparative advantage and technology levels, we also examined intra-industry trade and unit values of bilateral Korea-China trade, and semi-conductor industry technology. We found that the revealed comparative advantage has moved from low technology products to high technology products in Korea. China still maintains a comparative advantage in low technology products such as textiles and clothing, but at the same time, China’s high and medium-high technology products have recently gained a comparative advantage. The perception that China only has a comparative advantage for labor intensive products with low technology should be changed based on our analysis. However, China’s advancement in technology should not be overestimated. When comparing the unit value of basic materials of Korea’s and China’s exports, we found that Korea’s export product prices are on average higher than that of China’s, although the gap is reducing. A wider technology gap between Korea and China still exists in the semi-conductor industry, which is one of the most advanced high technology industries throughout the world.