Search results

Aero-engine exhaust plume length can be more than the aircraft length, making it easier to detect and track by infrared seeker. Aim of this study is to analyze the effect of free stream Mach number (M_∞) on length of potential core of plume. Also, change in infrared (IR) signature of plume and aircraft surface with variation in elevation angle (θ) is examined.

Convergent divergent (CD) nozzle is located outside the rear fuselage of the aircraft. A two dimensional axisymmetric computational fluid dynamics (CFD) study was carried out to study effect of M_∞ on potential core. The CFD data with aircraft and plume was then used for IR signature analysis. The sensor position is changed with respect to aircraft from directly bottom towards frontal section of aircraft. The IR signature is studied in mid wave IR (MWIR) and long wave IR (LWIR) band.

The potential plume core length and width increases as M_∞ increases. At higher altitudes, the potential core length increases for a fixed M_∞. The plume emits radiation in the MWIR band, whereas the aerodynamically heated aircraft surface emits IR in the LWIR band. The IR signature in the MWIR band continuously decreases as the sensor position changes from directly bottom towards frontal. In the LWIR band the IR signature initially decreases as the sensor moves from the directly bottom to the frontal, as the sensor begins to see the wing leading edges and nose cone, the IR signature in the LWIR band slightly increases.

The novelty of this study comes from the data reported on the effect of free stream Mach number on the potential plume core and variation of the overall IR signature of aircraft with change in elevation angle from directly below towards frontal section of aircraft.

Reducing aircraft fuel consumption has become a paramount research area, focusing on optimizing operational parameters like speed and altitude during the cruise phase. However, the existing methods for fuel reduction often rely on complex experimental calculations and data extraction from embedded systems, making practical implementation challenging. To address this, this study aims to devise a simple and accessible approach using available information.

In this paper, a novel analytic method to estimate and optimize fuel consumption for aircraft equipped with jet engines is proposed, with a particular emphasis on speed and altitude parameters. The dynamic variations in weight caused by fuel consumption during flight are also accounted for. The derived fuel consumption equation was rigorously validated by applying it to the Boeing 737–700 and comparing the results against the fuel consumption reference tables provided in the Boeing manual. Remarkably, the equation yielded closely aligned outcomes across various altitudes studied. In the second part of this paper, a pioneering approach is introduced by leveraging the particle swarm optimization algorithm (PSO). This novel application of PSO allows us to explore the equation’s potential in finding the optimal altitude and speed for an actual flight from Algiers to Brussels.

The results demonstrate that using the main findings of this study, including the innovative equation and the application of PSO, significantly simplifies and expedites the process of determining the ideal parameters, showcasing the practical applicability of the approach.

The suggested methodology stands out for its simplicity and practicality, particularly when compared to alternative approaches, owing to the ready availability of data for utilization. Nevertheless, its applicability is limited in scenarios where zero wind effects are a prevailing factor.

The research opens up new possibilities for fuel-efficient aviation, with a particular focus on the development of a unique fuel consumption equation and the pioneering use of the PSO algorithm for optimizing flight parameters. This study’s accessible approach can pave the way for more environmentally conscious and economical flight operations.

Unconventional machining processes, particularly ultrasonic vibration cutting (UVC), can overcome such technical bottlenecks. However, the precise mechanism through which UVC affects the in-service functional performance of advanced aerospace materials remains obscure. This limits their industrial application and requires a deeper understanding.

The surface integrity and in-service functional performance of advanced aerospace materials are important guarantees for safety and stability in the aerospace industry. For advanced aerospace materials, which are difficult-to-machine, conventional machining processes cannot meet the requirements of high in-service functional performance owing to rapid tool wear, low processing efficiency and high cutting forces and temperatures in the cutting area during machining.

To address this literature gap, this study is focused on the quantitative evaluation of the in-service functional performance (fatigue performance, wear resistance and corrosion resistance) of advanced aerospace materials. First, the characteristics and usage background of advanced aerospace materials are elaborated in detail. Second, the improved effect of UVC on in-service functional performance is summarized. We have also explored the unique advantages of UVC during the processing of advanced aerospace materials. Finally, in response to some of the limitations of UVC, future development directions are proposed, including improvements in ultrasound systems, upgrades in ultrasound processing objects and theoretical breakthroughs in in-service functional performance.

This study provides insights into the optimization of machining processes to improve the in-service functional performance of advanced aviation materials, particularly the use of UVC and its unique process advantages.

Designing new aircraft that are state-of-the-art and beyond always requires the development of new technologies. This paper aims to present lessons learned while designing, building and testing new UAVs in the configuration of the flying wing. The UAV contains a number of aerodynamic devices that are not obvious solutions and use the latest manufacturing technology achievements, such as 3D printing.

The design solutions were applied on an airworthy aircraft and checked during test flights. The process was first conducted on the smaller UAV, and based on the test outcomes, improvements were made and then applied on the larger version of the UAV, where they were verified.

A number of practical findings were identified. For example, the use of 3D printing technology for manufacturing integrated pressure ports, investigation of the adverse yaw effect on the flying wing configuration and the effectiveness of winglet rudders in producing yawing moment.

All designed devices were tested in practice on the flying aircraft. It allowed for improved aircraft performance and handling characteristics. Several of the technologies used improved the speed and quality of aerodynamic device design and manufacturing, which also influences the reliability of the aircraft.

The paper presents how 3D printing technology can be utilized for manufacturing of aerodynamic devices. Specially developed techniques for control surface design, which can affect adverse yaw problem and aircraft handling characteristics, were described.

In this study, the performance analysis of the split flow turbofan engine with afterburners has been examined using the parametric cycle analysis method. The purpose of this study is to examine how engine performance is impacted by design parameters and flight ambient values and to develop a software in this context.

Software has been developed using the open-source PYTHON programming language to perform performance analysis. Mach number, compressor/fan pressure ratio, bypass ratio and density were used as parameters. The effects of these variables on engine performance parameters were investigated.

Parametric cycle analysis has been calculated for different flight conditions in the range of 0–2 M and 0–15,000 m altitude for turbofan engines. With this study, basic data were obtained to optimize according to targeted flight conditions.

As a result of the performance analysis, the association between the flight conditions and design parameters of engine were determined. A software has been developed that can be used in the design of supersonic gas turbine engines for fast and easy simulation of the design parameters.

The variables used in the literature have been analyzed, and the results of the studies have been incorporated into the developed software, which can be used in innovative engine design. Software is capable to be developed further with the integration of new algorithms and models.

The purpose of this paper is to present a comparative study of flight circumstances, dynamic stability characteristics and controllability for two transport aircraft in severe atmospheric turbulence at transonic cruise flight for the purpose to obtain the prevention concepts of injuries to passengers and crew members for pilot training in International Air Transport Association (IATA) – Loss of Control In-flight (LOC-I) program.

A twin-jet and a four-jet transport aircraft encountering severe atmospheric turbulence are the study cases for this paper. The nonlinear unsteady aerodynamic models are established through flight data mining and the fuzzy-logic modeling technique based on the flight data of flight data recorder. This method can be adopted to examine the influence of horizontal wind shear and crosswind on loss of control, dynamic stability characteristics and controllability for transport aircraft in different weights and different sizes in tracking aviation safety of existing different types of aircraft.

The horizontal wind shear or crosswind before the turbulence encounter will easily induce rolling motion and then initiate the sudden plunging motion during the turbulence encounter. The roll rate will increase the oscillatory rolling motion during plunging motion, if the rolling damping is insufficient. The drop-off altitude will be enlarged by the oscillatory rolling motion during the sudden plunging motion.

A lack of the measurement data of vertical wind speed sensor on board to verify the estimated values of damping term is one of the research limitations for this study. The fact or condition of being severe in sudden plunging motion can be judged through the analysis of oscillatory derivatives with both dynamic stability and damping terms.

The roll rate will increase the oscillatory rolling motion during plunging motion, if the rolling damping is insufficient. The drop-off altitude will be enlarged by the oscillatory rolling motion during the sudden plunging motion. The horizontal wind shear or crosswind before the turbulence encounter will easily induce rolling motion and then initiated the sudden plunging motion during the turbulence encounter. If the drift angle is large, to turn off the autopilot of yaw control first and stabilize the rudder by the pedal. When passing through the atmosphere turbulence area, the pilots do not need to amend the heading angle urgently.

The flight safety prevention in avoidance of injuries for passengers and cabin crews is essential for the airlines. The horizontal wind shear or crosswind before the turbulence encounter will easily induce rolling motion and then initiated the sudden plunging motion during the turbulence encounter.

The flight safety prevention in avoidance of injuries for passengers and cabin crews is essential. The present assessment method is an innovation to examine the loss of control problems of aviation safety and promote the understanding of aerodynamic responses of the jet transport aircraft. It is expected to provide a valuable lecture for the international training courses for IATA – LOC-I program after this paper is being published.

A combustor design is a particularly important and difficult task in the development of gas turbine engines. During studies for accurate and easy combustor design, reasonable design methodologies have been established and used in engine development. The purpose of this paper is to review the design methodology for combustor in development of advanced gas turbine engines. The advanced combustor development task can be successfully achieved in less time and at lower cost by adopting new and superior design methodologies.

The review considers the main technical problems (combustion, cooling, fuel injection and ignition technology) in the development of modern combustor design and deals with combustor design methods by dividing it into preliminary design, performance evaluation, optimization and experiment. The advanced combustion and cooling technologies mainly used in combustor design are mentioned in detail. In accordance with the modern combustor design method, the design mechanisms are considered and the methods used in every stage of the design are reviewed technically.

The improved performances and strict emission limits of gas turbine engines require the application of advanced technologies when designing combustors. The optimized design mechanism and reasonable performance evaluation methods are very important in reducing experiments and increasing the effectiveness of the design.

This paper provides a comprehensive review of the design methodology for the advanced gas turbine engine combustor.

This paper aims to assess the impact of electrifying the environmental control system (ECS) and ice protection system (IPS), the primary pneumatic system consumers in a conventional commercial transport aircraft, on aircraft weight, range, and fuel consumption.

The case study was carried out on Airbus A321-200 aircraft. Design, modelling and analysis processes were carried out on Pacelab SysArc software. Conventional and electrical ECS and IPS architectures were modelled and analysed considering different temperature profiles.

The simulation results have shown that the aircraft model with ±270 VDC ECS and IPS architecture is lighter, has a more extended range and has less relative fuel consumption. In addition, the simulation results showed that the maximum range and relative fuel economy of all three aircraft models increased slightly as the temperature increased.

Considering the findings in this paper, it is seen that the electrification of the conventional pneumatic system in aircraft has positive contributions in terms of weight, power consumption and fuel consumption.

The positive contributions in terms of weight, power consumption and fuel consumption in aircraft will be direct environmental and economic contributions.

Apart from the conventional ECS and IPS of the aircraft, two electrical architectures, 230 VAC and ±270 VDC, were modelled and analysed. To see the effects of the three models created in different temperature profiles, analyses were done for cold day, ISA standard day and hot day temperature profiles.

In the aerial transportation area, fuel costs are critical to the economic viability of companies, and so urgent measures should be adopted to avoid any unnecessary increase in operational costs. In particular, this paper addresses the case of missed approach manouevres, showing that it is still possible to optimize the usual procedure.

The costs involved in a standard procedure following a missed approach are analysed through a simulation model, and they are compared with the improvements achieved with a fast reinjection scheme proposed in a prior work.

Experimental results show that, for a standard A320 aircraft, fuel savings ranging from 55% to 90% can be achieved through the reinjection method.

To the best of the authors’ knowledge, this work is the first study in the literature addressing the fuel savings benefits obtained by applying a reinjection technique for missed approach manoeuvres.

This study aims to elaborate on the existing link between maintenance practices and the digital world while also highlighting any unaddressed potential for digital transformation in aircraft maintenance. Additionally, explore how digital technologies contribute to optimizing efficiency within the continuing airworthiness management (CAM) processes.

A literature review was performed to provide a precise review of the authority regulations on CAM processes and existing literature on digital transformation, including artificial intelligence, machine learning, neural network and big data in civil aircraft maintenance and continuing airworthiness processes. This method is used to organize, analyze and structure the body of literature to identify research gaps in the selected scope of the study.

The high position of digital technologies in preventive and predictive maintenance and the need for legislative development for using them in CAM are emphasized. Moreover, it is shown in which area of CAM scientific research has been performed regarding the application of frontier digital technologies. In addition, the gaps between maintenance practices and the digital world, along with the potential scopes of digital transformation which has not been well addressed, are identified. And finally, how digital technologies can effectively increase efficiency in CAM processes is discussed.

To the best of our knowledge, no study comprehensively determined the body of existing knowledge on the aspects of digitalization related to the field of continuing airworthiness management and aircraft maintenance. The results of this study provide a positive contribution to airlines, policymakers, manufacturers and maintenance organizations achieving additional benefits from the implementation of digital technologies in the CAM processes.