Search results

The Presidential Address to the Liverpool Engineering Society by Mr. Farthing (the salient points of which are reproduced in this issue) has particular bearing upon lubrication and especially on young lubrication engineers. Mr. Farthing stressed the very wide field open to young engineers and the difficulties associated with training in order to cover as wide a field as may be necessary. It is usually so important to gain a wide knowledge before one can specialise and this is certainly the case with lubrication engineers. One cannot begin to fully appreciate the intricacies of a lubrication system with all its accessory components lubricating and guarding, for example, a large motive power plant or rolling mill, until one has more than a mere working knowledge of the plant itself, the duties it must perform, how it performs them and the snags that arise which might be overcome by correct lubrication. In view of the fact that lubrication systems are just as important in a textile mill as in a power station or a large brick works, the almost impossible‐to‐achieve‐range of knowledge that would simplify the work of a lubrication engineer is very obvious. Fortunately, lubricating principles apply to most cases and knowing how to apply one's knowledge from basic principles is the key to success in this difficult profession.

The breakdown of laminar flow in the clearance space of a journal is considered, and the point of transition is considered in relation to experiments carried out with ‘bearings’ of large clearance. Experiments involving flow visualization with very large clearance ratios of 0.05 to 0.3 show that the laminar regime gives way to cellular or ring vertices at the critical Reynolds number predicted by G. I. Taylor for concentric cylinders even in the presence of an axial flow and at a rather higher Reynolds number in the case of eccentric cylinders. The effect of the transition on the axial flow between the cylinders is small. The critical speed for transition as deduced by Taylor, is little affected by moderate axial flows and is increased by eccentricity. The effect of critical condition on the axial‐flow characteristics of the bearing system appears to be negligible, again for moderate axial flows. Assuming that the results can be extrapolated to clearances applicable to bearing operation, the main conclusion of this paper is that the breakdown of laminar flow, which is a practical possibility in very high‐speed bearings, is delayed by eccentric operation.

A method extensively used in the production of optically flat and finely finished surfaces is that of lapping the surface upon a plate using a loose abrasive mixed into a slurry form with a carrying fluid. If the surfaces finished in this way are in continuous or intermittent sliding contact, it is the author's opinion that any abrasives retained in their surfaces will affect surface wear. This paper reported on some exploratory work to indicate the degree of embedment of abrasive in certain materials lapped by hand.

The effects of space environment on friction and wear and on the selection of lubricants and self‐lubricating materials for spacecraft mechanisms are discussed, with special emphasis on the ultrahigh vacuum of space. Experimental studies have demonstrated the feasibility of using selected oils and greases to lubricate lightly loaded ball bearings without replenishment for periods of over one year under the following conditions of operation : speeds of 8,000 rpm, temperatures of 160 to 200°F., and vacuum of 10–8 torr. Over one‐half year of successful operation has been achieved under similar operating conditions with self‐lubricating retainers of reinforced Teflon, provided that the loads were light. Bonded films of molybdenum disulfide have given shorter lifetimes and poor repro‐ducibility. Metal‐to‐metal slip‐ring contacts introduce excessive electrical noise into circuits when operated in vacuum of 10–7 torr. The noise (as well as the friction and wear) can be markedly reduced by providing a small amount of oil vapor, sufficient to maintain a pressure on the order of 10–6 torr, or by incorporating molybdenum disulfide into the brush material.

A point in the operation of journal bearings under hydrodynamic or thick film conditions which has always excited controversy is the question of the negative pressures predicted in the classical theory. This note examines relevant theoretical and experimental evidence of conditions in the low pressure regions in journal bearing oil films, referring particularly to possible cavitation phenomena and making suggestions for further research.

In order to succeed in an action under the Equal Pay Act 1970, should the woman and the man be employed by the same employer on like work at the same time or would the woman still be covered by the Act if she were employed on like work in succession to the man? This is the question which had to be solved in Macarthys Ltd v. Smith. Unfortunately it was not. Their Lordships interpreted the relevant section in different ways and since Article 119 of the Treaty of Rome was also subject to different interpretations, the case has been referred to the European Court of Justice.

Compliant foil thrust bearings are promising bearings for high-speed oil-free turbomachinery. However, most previous experimental and numerical approaches to investigate the performance of these bearings have ignored the effect of bearing runner misalignment. Therefore, this paper aims to evaluate the effects of static and dynamic angular misalignments of the bearing runner on the performance of a gas-lubricated foil thrust bearing.

The bearing runner is allowed a maximum angular misalignment that produces a minimum gas film thickness as low as 20 per cent of the nominal clearance. Then, the variations of bearing load carrying capacity, viscous power loss and stiffness and damping coefficients of the gas film with runner misalignment are thoroughly analyzed. The flow in the gas film is modeled with compressible Reynolds equation along with the Couette approximation technique, and the deformation of the compliant bearing is calculated with a robust analytical model. Small perturbations method is used to calculate the force and moment dynamic coefficients of the gas film.

The results show that misaligned foil thrust bearings are capable of developing a restoring moment sufficient enough to withstand the imposed misalignments. Furthermore, the enhanced hydrodynamic effect ensures a stable operation of the misaligned bearing, and the results highlighted the role of the compliant bearing structure to maintain foil bearing prominent features even at misaligned conditions.

The value of this study is the evaluation of the effects of runner angular misalignments on the static and dynamic characteristics of Generation II bump-type foil thrust bearing.

According to the Christensen stochastic roughness model, the purpose of this study is to developing a modified Reynolds equation to investigate the effects of surface roughness and molecular rarefaction on ultra‐thin compressible and isothermal gas lubrication.

Basing upon the average film thickness method with three adjustable coefficients, the higher order slip‐flow velocity distribution was accommodated.

Compared to the smooth case, the longitudinal roughness improves the pressure distribution and load carrying capacity, while the effect of transverse roughness is opposite to that of longitudinal one. The molecular rarefaction effect may diminish the built‐up air bearing pressure and reduce the roughness effect on load carrying capacity. The squeeze number has evident effect in depression of maximum pressure of slider rail with transverse roughness.

Combing the high‐order slip‐flow model and Christensen roughness model, this research paper proposed a feasible study of the analysis of molecular rarefaction effect on slider air‐bearing system.

The Equal Pay Act 1970 (which came into operation on 29 December 1975) provides for an “equality clause” to be written into all contracts of employment. S.1(2) (a) of the 1970 Act (which has been amended by the Sex Discrimination Act 1975) provides:

The Howard Shuttering Contractors case throws considerable light on the importance which the tribunals attach to warnings before dismissing an employee. In this case the tribunal took great pains to interpret the intention of the parties to the different site agreements, and it came to the conclusion that the agreed procedure was not followed. One other matter, which must be particularly noted by employers, is that where a final warning is required, this final warning must be “a warning”, and not the actual dismissal. So that where, for example, three warnings are to be given, the third must be a “warning”. It is after the employee has misconducted himself thereafter that the employer may dismiss.