Search results

The purpose of this paper is to mount Gurney flaps at the trailing edges of the canards and investigate their influence on aerodynamic characteristics of a simplified canard-configuration aircraft model.

A force measurement experiment was conducted in a low-speed wind tunnel. Hence, the height and shape effects of the Gurney flaps on the canards were investigated.

Gurney flaps can increase the lift and pitching-up moment for the aircraft model tested, thereby increasing the lift when trimming the aircraft. The dominant parameter to influence aerodynamic characteristics is the height of Gurney flaps. When the flap heights are the same, the aerodynamic efficiency of the triangular Gurney flaps is higher than that of the rectangular ones. Moreover, the canard deflection efficiency will be reduced with Gurney flaps equipped, but the total aerodynamic increment is considerable.

This paper helps to solve the key technical problem of increasing take-off and landing lift coefficients, thus improving the aerodynamic performance of the canard-configuration aircraft.

This paper recommends to adopt triangular Gurney flaps with the height of 3 per cent chord length of the canard root (c) for engineering application.

To solve the problems of short battery life and low transportation safety of logistics drones, this paper aims to propose a design of logistics unmanned aerial vehicles (UAV) wing with a composite ducted rotor, which combines fixed wing and rotary-wing.

This UAV adopts tiltable ducted rotor combined with fixed wing, which has the characteristics of fast flight speed, large carrying capacity and long endurance. At the same time, it has the hovering and vertical take-off and landing capabilities of the rotary-wing UAV. In addition, aerodynamic simulation analysis of the composite model with a fixed wing and a ducted rotor was carried out, and the aerodynamic influence of the composite model on the UAV was analyzed under different speeds, fixed wing angles of attack and ducted rotor speeds.

The results were as follows: when the speed of the ducted rotor is 2,500 rpm, CL and K both reach maximum values. But when the speed exceeds 3,000 rpm, the lift will decrease; when the angle of attack of the fixed wing is 10° and the rotational speed of the ducted rotor is about 3,000 rpm, the aerodynamic characteristics of the wing are better.

The novelty of this work comes from a composite wing design of a fixed wing combined with a tiltable ducted rotor applied to the logistics UAVs, and the aerodynamic characteristics of the design wing are analyzed.

With aims to increase the aerodynamic efficiency of aerodynamic surfaces, study on flow control over these surfaces has gained importance. With the addition of flow control devices such as synthetic jets and vortex generators, the flow characteristics can be modified over the surface and, at the same time, enhance the performance of the body. One such flow control device is the tubercle. Inspired by the humpback whale’s flippers, these leading-edge serrations have improved the aerodynamic efficiency and the lift characteristics of airfoils and wings. This paper aims to discusses in detail the flow physics associated with tubercles and their effect on swept wings.

This study involves a series of experimental and numerical analyses that have been performed on four different wing configurations, with four different sweep angles corresponding to 0°, 10°, 20° and 30° at a low Reynolds number corresponding to Re_c=100,000.

Results indicate that the effect of tubercles diminishes with an increase in wing sweep. A significant performance enhancement was observed in the stall and post-stall regions. The addition of tubercles led to a smooth post-stall lift characteristic compared to the sudden loss in the lift with regular wings. Among the four different wings under observation, it was found that tubercles were most effective on the 0° configuration (no sweep), showing a 10.8% increment in maximum lift and a 38.5% increase in the average lift generated in the post-stall region. Tubercles were least effective on 30° configuration. Furthermore, with an increase in wing sweep, co-rotating vortices were distinctly observed rather than counter-rotating vortices.

While extensive numerical and experimental studies have been performed on straight wings with tubercles, studies on the tubercle effect on swept wings at low Reynolds number are minimal and mainly experimental in nature. This study uses numerical methods to explore the complex flow physics associated with tubercles and their implementation on swept wings. This study can be used as an introductory study to implement passive flow control devices in the low Reynolds number regime.

This paper aims to describe the selection of the ideal variable inlet concept group by using results of aerodynamic investigations, system safety analyses and integration studies.

Aerodynamic and functional inlet requirements are explained and variable inlet concept groups are introduced. The concept evaluation by means of a weighted point rating is presented. The respective concept groups are analysed and evaluated regarding economic, functional and safety requirements.

By means of this evaluation, the concept group that adjusts the inlet geometry by rigid segment repositioning is identified as most suitable concept group.

The early selection of the most suitable concept group enables more detailed subsequent concept investigations, potentially enabling the technology of variable inlets for future commercial aircraft.

This research is associated with the real-time parameters of wide- and narrow-body aircraft to recognize the quantitative relationship framework. This paper aims to find the superiority of aircraft design technology which triggers the reduction in specific fuel consumption (SFC) and economic competitiveness.

The real case study is performed with 22 middle-of-the-market (MoM) aircraft. This paper develops a fuel burn mathematical model for mid-size transport aircraft by a multi-linear regression approach. In addition, sensitivity analysis is performed to establish the authentication of the fuel burn model.

The study reveals that the MoM aircraft would be the future aircraft design in terms of better fuel economy and carbon footprint. From the multi-regression analysis, it is observed that the logarithmic regression model is the best fit for estimating the SFC. Moreover, fineness ratio, aspect ratio, gross weight, payload weight fraction, empty weight fraction), fuel weight fraction, payload, wing loading, thrust loading, range, take-off distance, cruise speed and rate of climb are observed as the suitable parameters which provide the best fitness value as 0.9804.

Several existing literature reveals that a few research has been performed on the MoM aircraft with wide-body configuration. Moreover, mathematical modelling on the fuel consumption was insignificantly found. This study examines several parameters which affect the fuel consumption of a wide-body aircraft. A real-case study for design configurations, propulsive systems, performance characteristics and structural integrity parameters of 22 different MoM aircraft are performed. Moreover, multi-regression modelling is developed to establish the relation between SFC and other critical parameters.

The purpose of this paper is to improve autonomous flight performance of an unmanned aerial vehicle (UAV) having actively sweep angle morphing wing using simultaneous UAV and flight control system (FCS) design.

An UAV is remanufactured in the ISTE Unmanned Aerial Vehicle Laboratory. Its wing sweep angle can vary actively during flight. FCS parameters and wing sweep angle are simultaneously designed to optimize autonomous flight performance index using a stochastic optimization method called as simultaneous perturbation stochastic approximation (SPSA). Results obtained are applied for flight simulations.

Using simultaneous design process of an UAV having actively sweep angle morphing wing and FCS design, autonomous flight performance index is maximized.

Authorization of Directorate General of Civil Aviation in Turkey is crucial for real-time UAV flights.

Simultaneous UAV having actively sweep angle morphing wing and FCS design process is so beneficial for recovering UAV autonomous flight performance index.

Simultaneous UAV having actively sweep angle morphing wing and FCS design process achieves confidence, high autonomous performance index and simple service demands of UAV operators.

Composing a novel approach to improve autonomous flight performance index (e.g. less settling and rise time, less overshoot meanwhile trajectory tracking) of an UAV and creating an original procedure carrying out simultaneous UAV having actively sweep angle morphing wing and FCS design idea.

This study aims to complete the optimization design of a centrifugal impeller with both high aerodynamic efficiency and good structural machinability.

First, the design parameters were derived from the blade loading distribution and the meridional geometry in the impeller three-dimensional (3D) inverse design. The blade wrap angle at the middle span surface and the spanwise averaged blade angle at the blade leading edge obtained from inverse design were chosen as the machinability objectives. The aerodynamic efficiency obtained by computational fluid dynamics was selected as the aerodynamic performance objective. Then, using multi-objective optimization with the optimal Latin hypercube method, quadratic response surface methodology and the non-dominated sorting genetic algorithm, the trade-off optimum impellers with small blade wrap angles, large blade angles and high aerodynamic efficiency were obtained. Finally, computational fluid dynamics and computer-aided manufacturing were performed to verify the aerodynamic performance and structural machinability of the optimum impellers.

Providing the fore maximum blade loading distribution at both the hub and shroud for the 3D inverse design helped to promote the structural machinability of the designed impeller. A straighter hub coupled with a more curved shroud also facilitated improvement of the impeller’s structural machinability. The preferred impeller was designed by providing both the fore maximum blade loading distribution at a relatively straight hub and a curved shroud for 3D inverse design.

The machining difficulties of the designed high-efficiency impeller can be reduced by reducing blade wrap angle and enlarging blade angle at the beginning of impeller design. It is of practical value in engineering by avoiding the follow-up failure for the machining of the designed impeller.

This paper aims to achieve an optimum flow separation control over the airfoil using a passive flow control method by introducing a bio-inspired nose near the leading edge of the National Advisory Committee for Aeronautics (NACA) 4 and 6 series airfoil. In addition, to find the optimised leading edge nose design for NACA 4 and 6 series airfoils for flow separation control.

Different bio-inspired noses that are inspired by the cetacean species have been analysed for different NACA 4 and 6 series airfoils. Bio-inspired nose with different nose length, nose depth and nose circle diameter have been analysed on airfoils with different thicknesses, camber and camber locations to understand the aerodynamic flow properties such as vortex formation, flow separation, aerodynamic efficiency and moment.

The porpoise nose design that has a leading edge with depth = 2.25% of chord, length = 0.75% of chord and nose diameter = 2% of chord, delays the flow separation and improves the aerodynamic efficiency. Average increments of 5.5% to 6° in the lift values and decrements in parasitic drag (without affecting the pitching moment) for all the NACA 4 and 6 series airfoils were observed irrespective of airfoil geometry such as different thicknesses, camber and camber location.

The two-dimensional computational analysis is done for different NACA 4 and 6 series airfoils at low subsonic speed.

This design improves aerodynamic performance and increases the structural strength of the aircraft wing compared to other conventional high lift devices and flow control devices. This universal leading edge flow control device can be adapted to aircraft wings incorporated with any NACA 4 and 6 series airfoil.

The results would be of significant interest in the fields of aircraft design and wind turbine design, lowering the cost of energy and air travel for social benefits.

Different bio-inspired nose designs that are inspired by the cetacean species have been analysed for NACA 4 and 6 series airfoils and universal optimum nose design (porpoise airfoil) is found for NACA 4 and 6 series airfoils.

The purpose of this study is to investigate the aerodynamic characteristics of a low-to-moderate-aspect-ratio, tapered, untwisted, unswept wing, equipped of sheared wing tips.

In this work, wind tunnel tests were made to study the influence in aerodynamic characteristics over a typical low-to-moderate-aspect-ratio wing of a general aviation aircraft, equipped with sheared – swept and tapered planar – wing tips. An experimental parametric study of different wing tips was tested. Variations in its leading and trailing edge sweep angle as well as variations in wing tip taper ratio were considered. Sheared wing tips modify the flow pattern in the outboard region of the wing producing a vortex flow at the wing tip leading edge, enhancing lift at high angles of attack.

The induced drag is responsible for nearly 50% of aircraft total drag and can be reduced through modifications to the wing tip. Some wing tip models present complex geometries and many of them present benefits in particular flight conditions. Results have demonstrated that sweeping the wing tip leading edge between 60 and 65 degrees offers an increment in wing aerodynamic efficiency, especially at high lift conditions. However, results have demonstrated that moderate wing tip taper ratio (0.50) has better aerodynamic benefits than highly tapered wing tips (from 0.25 to 0.15), even with little less wing tip leading edge sweep angle (from 57 to 62 degrees). The moderate wing tip taper ratio (0.50) offers more wing area and wing span than the wings with highly tapered wing tips, for the same aspect ratio wing.

Although many studies have been reported on the aerodynamics of wing tips, most of them presented complex non-planar geometries and were developed for cruise flight in high subsonic regime (low lift coefficient). In this work, an exploration and parametric study through wind tunnel tests were made, to evaluate the influence in aerodynamic characteristics of a low-to-moderate-aspect-ratio, tapered, untwisted, unswept wing, equipped of sheared wing tips (wing tips highly swept and tapered).

For an axial-flow compressor rotor, the upstream inflow conditions will vary as the aircraft faces harsh flight conditions (such as taking off, landing or maneuvering) or the whole compressor operates at off-design conditions. With the increase of upstream boundary layer thickness, the rotor blade tip will be loaded and the increased blade load will deteriorate the shock/boundary layer interaction and tip leakage flows, resulting in high aerodynamic losses in the tip region. The purpose of this paper is to achieve a better flow control for tip secondary flows and provide a probable design strategy for high-load compressors to tolerate complex upstream inflow conditions.

This paper presents an analysis and application of shroud wall optimization to a typical transonic axial-flow compressor rotor by considering the inlet boundary layer (IBL). The design variables are selected to shape the shroud wall profile at the tip region with the purpose of controlling the tip leakage loss and the shock/boundary layer interaction loss. The objectives are to improve the compressor efficiency at the inlet-boundary-layer condition while keeping its aerodynamic performance at the uniform condition.

After the optimization of shroud wall contour, aerodynamic benefits are achieved mainly on two aspects. On the one hand, the shroud wall optimization has reduced the intensity of the tip leakage flow and the interaction between the leakage and main flows, thereby decreasing the leakage loss. On the other hand, the optimized shroud design changes the shock structure and redistributes the shock intensity in the spanwise direction, especially weakening the shock near the tip. In this situation, the shock/boundary layer interaction and the associated flow separations and wakes are also eliminated. On the whole, at the inlet-boundary-layer condition, the compressor with optimized shroud design has achieved a 0.8 per cent improvement of peak efficiency over that with baseline shroud design without sacrificing the total pressure ratio. Moreover, the re-designed compressor also maintains the aerodynamic performance at the uniform condition. The results indicate that the shroud wall profile has significant influences on the rotor tip losses and could be properly designed to enhance the compressor aerodynamic performance against the negative impacts of the IBL.

The originality of this paper lies in developing a shroud wall contour optimization design strategy to control the tip leakage loss and the shock/boundary layer interaction loss in a transonic compressor rotor. The obtained results could be beneficial for transonic compressors to tolerate the complex upstream inflow conditions.