Search results

The “chiralisation” of Euclidean polygonal tessellations is a novel, recent method which has been used to design new auxetic metamaterials with complex topologies and improved geometric versatility over traditional chiral honeycombs. This paper aims to design and manufacture chiral honeycombs representative of four distinct classes of 2D Euclidean tessellations with hexagonal rotational symmetry using fused-deposition additive manufacturing and experimentally analysed the mechanical properties and failure modes of these metamaterials.

Finite Element simulations were also used to study the high-strain compressive performance of these systems under both periodic boundary conditions and realistic, finite conditions. Experimental uniaxial compressive loading tests were applied to additively manufactured prototypes and digital image correlation was used to measure the Poisson’s ratio and analyse the deformation behaviour of these systems.

The results obtained demonstrate that these systems have the ability to exhibit a wide range of Poisson’s ratios (positive, quasi-zero and negative values) and stiffnesses as well as unusual failure modes characterised by a sequential layer-by-layer collapse of specific, non-adjacent ligaments. These findings provide useful insights on the mechanical properties and deformation behaviours of this new class of metamaterials and indicate that these chiral honeycombs could potentially possess anomalous characteristics which are not commonly found in traditional chiral metamaterials based on regular monohedral tilings.

To the best of the authors’ knowledge, the authors have analysed for the first time the high strain behaviour and failure modes of chiral metamaterials based on Euclidean multi-polygonal tessellations.

Because of the anisotropy of the process and the variability in the quality of printed parts, finite element analysis is not directly applicable to recycled materials manufactured using fused filament fabrication. The purpose of this study is to investigate the numerical-experimental mechanical behavior modeling of the recycled polymer, that is, recyclable polyethylene terephthalate (rPET), manufactured by a deposition FFF process under compressive stresses for new sustainable designs.

In all, 42 test specimens were manufactured and analyzed according to the ASTM D695-15 standards. Eight numerical analyzes were performed on a real design manufactured with rPET using Young's compression modulus from the experimental tests. Finally, eight additional experimental tests under uniaxial compression loads were performed on the real sustainable design for validating its mechanical behavior versus computational numerical tests.

As a result of the experimental tests, rPET behaves linearly until it reaches the elastic limit, along each manufacturing axis. The results of this study confirmed the design's structural safety by the load scenario and operating boundary conditions. Experimental and numerical results show a difference of 0.001–0.024 mm, allowing for the rPET to be configured as isotropic in numerical simulation software without having to modify its material modeling equations.

The results obtained are of great help to industry, designers and researchers because they validate the use of recycled rPET for the ecological production of real-sustainable products using MEX technology under compressive stress and its configuration for numerical simulations. Major design companies are now using recycled plastic materials in their high-end designs.

Validation results have been presented on test specimens and real items, comparing experimental material configuration values with numerical results. Specifically, to the best of the authors’ knowledge, no industrial or scientific work has been conducted with rPET subjected to uniaxial compression loads for characterizing experimentally and numerically the material using these results for validating a real case of a sustainable industrial product.

This study aims to deal with developing composite filaments and investigating the tribological behavior of additively manufactured syntactic foam composites. The primary objective is to examine the suitability of the cenosphere (CS; 0–30 Wt.%) to develop a high-quality lightweight composite structure with improved abrasion strength.

CS/polyethylene terephthalate glycol (PETG) composite feedstock filaments under optimized extrusion conditions were developed, and a fused filament fabrication process was used to prepare CS-filled PETG composite structures under optimal printing conditions. Significant parameters such as CS (0–30 Wt.%), sliding speed (200–800 rpm) and typical load (10–40 N) were used to minimize the dry sliding wear rate and coefficient of friction for developed composites.

The friction coefficient and specific wear rate (SWR) are most affected by the CS weight percentage and applied load, respectively. However, nozzle temperature has the least effect on the friction coefficient and SWR. A mathematical model predicts the composite material’s SWR and coefficient of friction with 87.5% and 95.2% accuracy, respectively.

Because of their tailorable physical and mechanical properties, CS/PETG lightweight composite structures can be used in low-density and damage-tolerance applications.

CS, an industrial waste material, is used to develop lightweight syntactic foam composites for advanced engineering applications.

CS-reinforced PETG composite filaments were developed to fabricate ultra-light composite structures through a 3D printing routine.

This paper aims to examine the static compression characteristics of cell topologies in body-centered cubic with vertical struts (BCCZ) and face-centered cubic with vertical struts (FCCZ) along with novel BCCZZ and FCCZZ lattice structures.

The newly developed structures were obtained by adding extra interior vertical struts into the BCCZ and FCCZ configurations. The samples, composed of the AlSi10Mg alloy, were fabricated using the selective laser melting (SLM) additive manufacturing technique. The specific compressive strength and failure behavior of the manufactured lattice structures were investigated, and comparative analysis among them was done.

The results revealed that the specific strength of BCCZZ and FCCZZ samples with 0.5 mm strut diameter exhibited approximately a 23% and 18% increase, respectively, compared with the BCCZ and FCCZ samples with identical strut diameters. Moreover, finite element analysis was carried out to simulate the compressive response of the lattice structures, which could be used to predict their strength and collapse mode. The findings showed that while the local buckling of lattice cells is the major failure mode, the samples subsequently collapsed along a diagonal shear band.

An original and systematic investigation was conducted to explore the compression properties of newly fabricated lattice structures using SLM. The results revealed that the novel FCCZZ and BCCZZ structures were found to possess significant potential for load-bearing applications.

The purpose of this study was conducted at an enterprise that produces fasteners and is one of the leading companies in the sector in terms of market share. Possible defects in the coating of bolts and nuts either lead to products being scrapped or all of the coating process being repeated from beginning to end. In both cases, the enterprise faces a waste of time and excessive costs. Through this project, the six sigma theory and its means were effectively used to improve the efficiency and quality management of the company. The selection of the six sigma project has also contributed to the creation of various documents to be used for project screening and evaluation of financial results.

Six sigma is an optimization strategy that is used to improve the profitability of businesses, avoid waste, scrap and losses, reduce costs and improve the effectiveness of all activities to meet or exceed customers’ needs and expectations. Six sigma’s process improvement model, known as Definition-Measurement-Analysis-Improvement-Control, contributes to the economic and technical achievements of businesses. The normal distribution of a process should be within ±3 sigma of the mean. This represents a scale of 99.7% certainty. However, improving the process through the utilization of the six sigma rule, which accepts normal variabilities of processes twice as strict, will result in an error rate of 3.4 per million instead of 2,700 per million for each product or service.

Using six sigma practices to reduce the costs associated with low quality and to increase economic added value became a cultural practice. With this, the continuation of six sigma practices throughout the Company was intended. The annual cost reduction achieved with the utilization of six sigma practices can be up to $21,780. When time savings are also considered, a loss reduction of about $30,000 each year can be achieved. The coating thickness efficiency increased from 85% to 95% after the improvements made through the six sigma project. There is a significant increase in the efficiency of coating thickness. In addition, the coating thickness efficiency is also close to the target value of 95%–97%.

The results of the study were optimized with the help of deep learning. The performance of the model created in deep learning was quite close to the actual performance. This result implicates the validity of the improvement work. The results may act as a guide for the use of deep learning in new projects.

Stab-resistant body armor (SRBA) is used to protect the body from sharp knives. However, most SRBA materials currently have the disadvantages of large weight and thickness. This paper aims to prepare lightweight and high-performance SRBA by 3D printing truss structure and resin-filling method.

The stab resistance truss structure was prepared by the fused deposition modeling method, and the composite structure was formed after filling with resin for dynamic and quasi-static stab tests. The optimized structural plate can meet the standard GA68-2019. Digital image correlation technology was used to analyze the local strain changes during puncture. The puncture failure mode was summarized by the final failure morphologies. The explicit dynamics module in ANSYS Workbench was used to analyze the design of the overlapped structure stab resistance process in this paper.

The stab resistance performance of the 3D-printed structural plate is affected by the internal filling pattern. The stab resistance performance of 3D-printed structural parts was significantly improved after resin filling. The 50%-diamond-PLA-epoxy, with a thickness of only 5 mm was able to meet the stab resistance standard. Resins are used to increase the strength and hardness of the material but also to increase crack propagation and reduce the toughness of the material. The overlapping semicircular structure was inspired by the exoskeleton structure of the demon iron beetle, which improved the stab resistance between gaps. The truss structure can effectively disperse stress for toughening. The filled resin was reinforced by absorbing impact energy.

The 3D-printed resin-filled truss structure can be used to prepare high-performance stab resistance structural plates, which balance the toughness and strength of the overall structure and ultimately reduce the thickness and weight of the SRBA.

This study aims to present an experimental approach to develop a high-strength 3D-printed recycled polymer composite reinforced with continuous metal fiber.

The continuous metal fiber composite was 3D printed using recycled and virgin acrylonitrile butadiene styrene-blended filament (RABS-B) in the ratio of 60:40 and postused continuous brass wire (CBW). The 3D printing was done using an in-nozzle impregnation technique using an FFF printer installed with a self-modified nozzle. The tensile and single-edge notch bend (SENB) test samples are fabricated to evaluate the tensile and fracture toughness properties compared with VABS and RABS-B samples.

The tensile and SENB tests revealed that RABS-B/CBW composite 3D printed with 0.7 mm layer spacing exhibited a notable improvement in Young’s modulus, ultimate tensile strength, elongation at maximum load and fracture toughness by 51.47%, 18.67% and 107.3% and 22.75% compared to VABS, respectively.

This novel approach of integrating CBW with recycled thermoplastic represents a significant leap forward in material science, delivering superior strength and unlocking the potential for advanced, sustainable composites in demanding engineering fields.

Limited research has been conducted on the in-nozzle impregnation technique for 3D printing metal fiber-reinforced recycled thermoplastic composites. Adopting this method holds the potential to create durable and high-strength sustainable composites suitable for engineering applications, thereby diminishing dependence on virgin materials.

This papers aims to study lattice structures in terms of geometric variables, manufacturing variables and material-based variants and their correlation with compressive behaviour for their application in a methodology for the design and development of personalized elastic therapeutic products.

Lattice samples were designed and manufactured using extrusion-based additive manufacturing technologies. Mechanical tests were carried out on lattice samples for elasticity characterization purposes. The relationships between sample stiffness and key geometric and manufacturing variables were subsequently used in the case study on the design of a pressure cushion model for validation purposes. Differentiated areas were established according to patient’s pressure map to subsequently make a correlation between the patient’s pressure needs and lattice samples stiffness.

A substantial and wide variation in lattice compressive behaviour was found depending on the key study variables. The proposed methodology made it possible to efficiently identify and adjust the pressure of the different areas of the product to adapt them to the elastic needs of the patient. In this sense, the characterization lattice samples turned out to provide an effective and flexible response to the pressure requirements.

This study provides a generalized foundation of lattice structural design and adjustable stiffness in application of pressure cushions, which can be equally applied to other designs with similar purposes. The relevance and contribution of this work lie in the proposed methodology for the design of personalized therapeutic products based on the use of individual lattice structures that function as independent customizable cells.

The research aims to develop an assessment framework that evaluates critical success factors (CSFs) for the Quality 4.0 (Q 4.0) transition among Indian firms.

The authors use the fuzzy-Delphi method to validate the results of a systematic literature review (SLR) that explores critical aspects. Further, the fuzzy decision-making trial and laboratory (DEMATEL) method determines the cause-and-effect link. The findings indicate that developing a Q 4.0 framework is essential for the long-term success of manufacturing companies. Utilizing the power of digital technology, data analytics and automation, manufacturing companies can benefit from the Q 4.0 framework. Product quality, operational effectiveness and overall business performance may all be enhanced by implementing the Q 4.0 transition framework.

The study highlights significant awareness of Q 4.0 in the Indian manufacturing sector that is acquired through various means such as training, experience, learning and research. However, most manufacturing industries in India still follow older quality paradigms. On the other hand, Indian manufacturing industries seem well-equipped to adopt Q 4.0, given practitioners' firm grasp of its concepts and anticipated benefits, including improved customer satisfaction, product refinement, continuous process enhancement, waste reduction and informed decision-making. Adoption hurdles involve challenges including reliable electricity access, high-speed Internet, infrastructure, a skilled workforce and financial support. The study also introduces a transition framework facilitating the shift from conventional methods to Q 4.0, aligned with the principles of the Fourth Industrial Revolution (IR).

This research exclusively examines the manufacturing sector, neglecting other fields such as medical, service, mining and construction. Additionally, there needs to be more emphasis on the Q 4.0 implementation frameworks within the scope of the study.

This may be the inaugural framework for transitioning to Q 4.0 in India's manufacturing sectors and, conceivably, other developing nations.