Search results

High‐frequency transducer arrays that can operate at frequencies above 30 MHz are needed for high‐resolution medical ultrasound imaging. The fabrication of such devices is challenging not only because of the fine‐scale piezocomposite fabrication typically required but also because of the small size of arrays and their interconnects. The purpose of this paper is to present an overview of research to develop solutions for several of the major problems in high‐frequency ultrasound array fabrication.

Net‐shape 1‐3 piezocomposites operating above 40 MHz are developed. High‐quality surface finishing makes photolithographic patterning of the array electrodes on these fine scale piezocomposites possible, thus establishing a fabrication methodology for high‐frequency kerfless ultrasound arrays.

Structured processes are developed and prototype components are made with them, demonstrating the viability of the selected fabrication approach. A 20‐element array operating at 30 MHz is patterned and characterised. Furthermore, an electrode pattern suitable for a 20‐element array operating at 100 MHz is created to demonstrate the state of the art of photolithography processing directly on piezocomposite.

The work reported suggests that ultrasound arrays for real‐time biomedical imaging will be viable at higher frequencies than presently available commercially or previously reported in the research literature.

The main elements of a novel, fully mask‐based process for high‐frequency ultrasound transducer array fabrication are presented in outline in this paper.

Since the importance role of ultrasonic tomography (UT) in industry, especially in oil industry, to produce noninvasive and nondestructive plane images, research on UT system with a metal pipe conveyor is investigated. The produced cross-sectional images are used for detecting the concentration of solid and liquid mixture inside the pipe, noninvasively. In practice, due to application of metal pipes as the conveyor of oil mixture so the capability of manufacturing an UT system with a metal pipe is investigated in this paper. The paper aims to discuss these issues.

Finite element software (COMSOL Multiphysics 3.5) for visualizing the structure of pipe with mounted sensors on the periphery of the pipe is used. The manner of ultrasonic wave propagation on different layers on various frequencies and finding the time of flight for transmission mode signal and lamb mode signal are achieved by the means of done simulations. Finding the proper ultrasonic sensor base on its efficiency is the main step of designing an UT system. This is done by estimating the resonance frequency of sensor due to the manner of ultrasonic wave propagation in different frequencies shown in simulation results.

Due to simulation results, lamb wave is a permanent propagation mode of ultrasonic wave which makes interference in measuring process of straight path signal and it is impossible to remove. Relief of the mentioned problem finding an optimum frequency to decrease the affection of lamb wave in detecting point. Optimum frequency of ultrasonic wave to satisfy the objective is 45 kHz which is measured by considering of mathematic of ultrasonic wave propagation in different layers. The reaching time of straight path signal and lamb wave signal in opposite sensor as the receiver are 5.5 and 4.6 μs, respectively.

This investigation is the first step to perform the UT in a noninvasive method to produce the cross-sectional images of metal pipe. Due to the wide application of metal pipes as the conveyor of the liquids/gases, metal pipe for the UT application is studied in this research.

The purpose of this study is to develop a reconstruction and measurement system for data analysis using ultrasonic transmission tomography. The problem of reconstruction from the projection is encountered in practical implementation, which consists in reconstructing an image that is an estimation of an unknown object from a finite set of projection data. Reconstructive algorithms used in transmission tomography are based on linear mathematical models, which makes it necessary to process non-linear data into estimates for a finite number of projections. The application of transformation methods requires building a mathematical model in which the projection data forming the known and unknown quantities are functions with arguments from a continuous set of real numbers, determining the function describing the unknown quantities sought in the form of inverse relation and adapting it to operate on discrete and noisy data. This was done by designing a tomographic device and proprietary algorithms capable of reconstructing two-dimensional images regardless of the size, shape, location or number of inclusions hidden in the examined object.

The application consists of a device and measuring sensors, as well as proprietary algorithms for image reconstruction. Ultrasonic transmission tomography makes it possible to analyse processes occurring in an object without interfering with the examined object. The proposed solution uses algorithms based on ray integration, the Fermat principle and deterministic methods. Two applications were developed, one based on C and implemented on the embedded device, while the other application was made in Matlab.

Research shows that ultrasonic transmission tomography provides an effective analysis of tested objects in closed tanks.

In the presented technique, the use of ultrasonic absorption wave has been limited. Nevertheless, the effectiveness of such a solution has been confirmed.

The presented solution can be used for research and monitoring of technological processes.

Author’s tomographic system consisting of a measuring system and image reconstruction algorithms.

This paper aims to present the details of isotactic polypropylene (it-PP) films with a cellular structure (air-cavities) dedicated to pressure sensors. The polymer composites (thin films enriched with 5 and 10 wt% of mineral fillers as Sillikolloid P 87 and glass beads) should exhibit suitable structural elasticity within specific stress ranges. After the deformation force is removed, the sensor material must completely restore its original shape and size.

Estimating the stiffness tensor element (C₃₃) for polymer films (nonpolar space-charge electrets) by broadband resonance ultrasound spectroscopy is a relatively simple method of determining the safe stress range generated in thin pressure sensors. Therefore, ultrasonic and piezoelectric studies were carried out on four composite it-PP films. First, the longitudinal velocity (v_L) of ultrasonic waves passing through the it-PP film in the z-direction (thickness) was evaluated from the ω-position of mechanical resonance of the so-called insertion loss function. In turn, the d₃₃ coefficient was calculated from accumulated piezoelectric charge density response to mechanical stress.

Research is at an early stage; however, it can be seen that the mechanical orientation of the it-PP film improves its piezoelectric properties. Moreover, the three-year electric charge stability of the it-PP film seems promising.

Ultrasonic spectroscopy can be successfully handled as a validation method in the small-lot production of polymer films with the air-cavities structure intended for pressure sensors. The structural repeatability of polymer films is strongly related to a homogeneous distribution of the electric charge on the electret surface.

Ultrasound is a well-established technology in medical science, though many of the conventional measurement systems (hydrophones and radiation force balances [RFBs]) often lack accuracy and tend to be expensive. This is a significant problem where sensors must be considered to be “disposable” because they inevitably come into contact with biological fluids and expense increases dramatically in cases where a large number of sensors in array form are required. This is inevitably the case where ultrasound is to be used for the in vitro growth stimulation of a large plurality of biological samples in tissue engineering. Traditionally only a single excitation frequency is used (typically 1.5 MHz), but future research demands a larger choice of wavelengths for which a single broadband measurement transducer is desirable. Furthermore, because of implementation conditions there can also be large discrepancies between measurements. The purpose of this paper deals with a very cost-effective alternative to expensive RFBs and hydrophones.

Utilization of cost-effective piezoelectric elements as broadband sensors.

Very effective results with equivalent (if not better) accuracy than expensive alternatives.

This paper concentrates on how very cost-effective piezoelectric ultrasound transducers can be implemented as sensors for ultrasound power measurements with accuracy as good, if not better than those achievable using radiation force balances or hydrophones.

Wireless sensor networks (WSN), as a solution for buried water pipe monitoring, face a new set of challenges compared to traditional application for above-ground infrastructure monitoring. One of the main challenges for underground WSN deployment is the limited range (less than 3 m) at which reliable wireless underground communication can be achieved using radio signal propagation through the soil. To overcome this challenge, the purpose of this paper is to investigate a new approach for wireless underground communication using acoustic signal propagation along a buried water pipe.

An acoustic communication system was developed based on the requirements of low cost (tens of pounds at most), low power supply capacity (in the order of 1 W-h) and miniature (centimetre scale) size for a wireless communication node. The developed system was further tested along a buried steel pipe in poorly graded SAND and a buried medium density polyethylene (MDPE) pipe in well graded SAND.

With predicted acoustic attenuation of 1.3 dB/m and 2.1 dB/m along the buried steel and MDPE pipes, respectively, reliable acoustic communication is possible up to 17 m for the buried steel pipe and 11 m for the buried MDPE pipe.

Although an important first step, more research is needed to validate the acoustic communication system along a wider water distribution pipe network.

This paper shows the possibility of achieving reliable wireless underground communication along a buried water pipe (especially non-metallic material ones) using low-frequency acoustic propagation along the pipe wall.

This study aims to understand the influence of megasonic (MS)-assisted agitation on printed circuit boards (PCBs) electroplated using copper (Cu) electrolyte solutions to improve plating efficiencies through enhanced ion transportation.

The impact of MS-assisted agitation on topographical properties of the electroplated surfaces was studied through a design of experiments by measuring surface roughness, which is characterised by values of the parameter Ra as measured by white light phase shifting interferometry and high-resolution scanning electron microscopy.

An increase in Ra from 400 to 760 nm after plating was recorded for an increase in acoustic power from 45 to 450 W. Roughening increased because of micro-bubble cavitation energy and was supported through direct imaging of the cavitation. Current thieving effect by the MS transducer induced low currents, leading to large Cu grain frosting and reduction in the board quality. Current thieving was negated in plating trials through specific placement of transducer. Wavy electroplated surfaces, due to surface acoustic waves, were also observed to reduce the uniformity of the deposit.

The formation of unstable transient cavitation and variation of the topology of the Cu surface are unwanted phenomena. Further plating studies using MS agitation are needed, along with fundamental simulations, to determine how the effects can be reduced or prevented.

This study can help identify manufacturing settings required for high-quality MS-assisted plating and promote areas for further investigation, leading to the development of an MS plating manufacturing technique.

This study quantifies the topographical changes to a PCB surface in response to MS agitation and evidence for deposited Cu artefacts due to acoustic effects.

One of the recent applications of fabrics is to use them for sound insulation. Accordingly, due to their low production cost and low relative density, fabrics have drawn attention in some of the industries such as the automotive and aircraft industries. The present study is aimed to investigate the effects of the fiber cross-section, porosity, thickness of samples and fuzzing of the knitted fabric on the sound absorption coefficient.

In the present study, fabrics with three different stitch densities were knitted by yarns consist of three different forms of fiber cross-section shapes (circular, elliptical and plus-shaped). In this work, the sound absorption coefficient of knitted fabrics was investigated with regard to the different fiber cross-sections and structural parameters using an impedance tube.

As indicated by the obtained results, the cross-section, porosity, thickness and mass per unit area of the fabrics were the determinant factors for the sound absorption coefficient. In addition to, the sound absorption coefficient and porosity were shown to have an inverse relationship.

A section of the present paper has been allocated to the investigation of the effect of the fiber cross-section and fuzzing of fabric on the sound absorption of plain knitted fabrics.

The purpose of this paper is to revisit the recursive computation of closed-form expressions for the topological derivative of shape functionals in the context of time-harmonic acoustic waves scattering by sound-soft (Dirichlet condition), sound-hard (Neumann condition) and isotropic inclusions (transmission conditions).

The elliptic boundary value problems in the singularly perturbed domains are equivalently reduced to couples of boundary integral equations with unknown densities given by boundary traces. In the case of circular or spherical holes, the spectral Fourier and Mie series expansions of the potential operators are used to derive the first-order term in the asymptotic expansion of the boundary traces for the solution to the two- and three-dimensional perturbed problems.

As the shape gradients of shape functionals are expressed in terms of boundary integrals involving the boundary traces of the state and the associated adjoint field, then the topological gradient formulae follow readily.

The authors exhibit singular perturbation asymptotics that can be reused in the derivation of the topological gradient function in the iterated numerical solution of any shape optimization or imaging problem relying on time-harmonic acoustic waves propagation. When coupled with converging Gauss−Newton iterations for the search of optimal boundary parametrizations, it generates fully automatic algorithms.

There are structural elements on the aircraft that may be exposed to high-intensity sound levels. One of them is an air inlet duct of the jet engine. To prepare data for the air duct damage tolerance analysis, flat panels were tested under acoustic loading. The paper aims to discuss this issue.

The acoustic fatigue test equipment for grazing wave’s incidence was designed based on the FE analyses. Flat composite panels were designed and manufactured using the Hexply 8552/AGP193-PW prepreg with the simulation of production imperfections or operational damage. The dynamic behaviour of panels has been tested using three regimes of acoustic loading: white noise spectrum, engine noise spectrum and discrete harmonic frequencies. The panel deflection was monitored along its longitudinal axis, and the ultrasonic NDT instruments were used for the monitoring of relevant delamination increments. The FE model of the panel was created in Abaqus to study panel dynamic characteristics.

No delamination progress was observed by NDT testing even if dynamic characteristics, especially modal frequency, of the panel changed during the fatigue test. Rayleigh damping coefficients were evaluated for their use in FE models. Significant differences were found between the measured and computed panel deflection curves near the edge of the panel.

The research results underscored the signification of the FE model boundary conditions and the element type selections when the panel works like a membrane rather than a plate because of their low bending stiffness.