Search results

This paper aims to find a suitable solution to degrade the C.I. Reactive Red 24 (RR24) dyeing wastewater by using sodium persulphate to recycle water and inorganic salts.

The effects of temperature, the concentration of inorganic salts and Na₂CO₃ and the initial pH value on the degradation of RR24 were studied. Furthermore, the relationship between free radicals and RR24 degradation effect was investigated. Microscopic routes and mechanisms of dye degradation were further confirmed by testing the degradation karyoplasmic ratio of the product. The feasibility of the one-bath cyclic dyeing in the recycled dyeing wastewater was confirmed through the properties of dye utilization and color parameters.

The appropriate conditions were 0.3 g/L of sodium persulphate and treatment at 95°C for 30 min, which resulted in a decolorization rate of 98.4% for the dyeing wastewater. Acidic conditions are conducive to rapid degradation of dyes, while ·OH or SO₄⁻· have a destructive effect on dyes under alkaline conditions. In the early stage of degradation, ·OH played a major role in the degradation of dyes. For sustainable cyclic dyeing of RR24, inorganic salts were reused in this dyeing process and dye uptake increased with the times of cycles. After the fixation, some Na₂CO₃ may be converted to other salts, thereby increasing the dye uptake in subsequent cyclic staining. However, it has little impact on the dye exhaustion rate and color parameters of dyed fabrics.

The recommended technology not only reduces the quantity of dyeing wastewater but also enables the recycling of inorganic salts and water, which meets the requirements of sustainable development and clean production.

The main aim of this study is to characterise and identify specific chemo-sensory profiles of ciders from the Canary Islands (Spain).

Commercial samples of Canary ciders were compared to ciders from the Basque Country and Asturias. In total, 18 samples were studied, six for each region. The analysis comprised their sensory profiling and chemical characterisation of their polyphenolic profile, volatile composition, conventional chemical parameters and CIELAB colour coordinates. In parallel, the sensory profile of the samples from the Canary Islands was first compared with their Basque and Asturian counterparts by labelled sorting task. Then, their specific aroma profile was characterised by flash profile. Further quantification of sensory-active compounds was performed by GC–MS and GC-FID to identify the volatile compounds involved in their aroma profile.

Results show that Canary ciders present a specific chemical profile characterised by higher levels of ethanol, and hydroxycinnamic acids, mainly t-ferulic, t-coumaric and neochologenic acids, and lower levels of volatile and total acidity than their Asturian and Basque counterparts. They also present a specific aroma profile characterised by fruity aroma, mainly fruit in syrup and confectionary, and sweet flavours related to their highest levels of vinylphenols formed by transformation of hydroxycinnamic acids.

An integrated strategy to explore the typicity of the currently existing Canary ciders in the market was developed. The results are important in that they will help other regions to identify specific typical chemo-sensory profiles and to promote the creation of certifications supporting regional typicity.

Agricultural waste and food sources are some of the pollutants of the environment. One of these wastes is the peel of fruits that cannot be consumed as food. In this regard, walnut husk (WH) and oleaster peel (PO) are known as two important sources of tannin and are bulky wastes. Because of the high percentage of tannin, these materials can be used as a natural source for the preparation of bio-mordant in the dyeing process.

In this study, Reseda and Madder were used as natural dyes in the presence of a mixture of two bio-mordants. WH and PO were selected as bio-mordant. All natural resources are extracted to obtain the juice. The phenolic percentage of tannin-containing extracts was evaluated and then it was used for wool yarns by premordanting method. The results of evaluating the fastness properties using the ISO method.

The most important achievement of this research is the use of agricultural waste in the dyeing process to reduce environmental pollution and create added value. All compounds rich in tannin have some phenolic components, therefore the amount of phenolic content of these extracts was evaluated. The effect of mixing the mordant on the color characteristics of the yarns was investigated and the results showed that changing the ratio of the combination of two mordant is effective on the K/S values. The results of evaluating the fastness properties using the ISO method showed that the washing, rubbing and light fastness in the presence of mordant is good, good and moderate, respectively.

In this paper, to the best of the authors’ knowledge, for the first time, the combination of two natural extracts obtained from agricultural waste has been used to create a new bio-mordant on fibers and improve stability.

This paper aims to synthesize 6-ethyl-4-hydroxyquinolin-2(1H)-one as a new enol-type coupling component in the preparation of some 3-arylazo-4-hydroxyquinolin-2(1H)-one dyes and evaluate the solvent effects on their absorption in ultraviolet-visible spectra.

6-Ethyl-4-hydroxyquinolin-2(1H)-one was synthesized by thermal cyclocondensation reaction of N, N′-bis(4-ethylphenyl) malonamide at 130–140°C in polyphosphoric acid. This compound was then applied in the azo-coupling reaction with some aniline-based diazonium salts, so as to prepare seven new mono-heterocyclic azo dyes. The structures of the compounds were confirmed using mass spectroscopic technique. Fourier transform infra red (FT-IR) and 1H proton nuclear magnetic resonance (1H NMR) and carbon-13 nuclear magnetic resonance (13 C NMR) studies on the structure of the azo compounds revealed that they exist as two E- and Z-isomers of hydrazone tautomer both in solid and solution state. The effects of acid and base on the visible absorption spectra of the dyes were also evaluated and discussed.

Ultra violet-visible UV-vis absorption spectra of the dyes didn’t show significant variation by changing of solvents because of intramolecular H-bonding between proposed hydrazone forms and 2- and 4-keto functions in their structures. The spectra of the dyes were not sensitive to the addition of acid but were very sensitive to base.

The synthesized 3-arylazo-4-hydroxyquinolin-2(1H)-one dyes are new members in the 4-hydroxyquinolin-2(1H)-one azo dyes family, where very few details regarding the synthesis of such dyes are reported before in the literature. They are unique in terms of synthesis and spectral properties.

Globally, consumer’s inclination towards functional foods had noticed due to their greater health consciousness coupled with enhanced health-care cost. The fact that probiotics could promote a healthier gut microbiome led projection of probiotic foods as functional foods and had emerged as an important dietary strategy for improved human health. It had established that ice cream was a better carrier for probiotics than fermented milked due to greater stability of probiotics in ice cream matrix. Global demand for ice cream boomed and probiotic ice cream could have been one of the most demanded functional foods. The purpose of this paper was to review the technological aspects and factors affecting probiotic viability and to standardize methodology to produce functional probiotic ice cream.

Attempt was made to search the literature (review and researched papers) to identify diverse factors affecting the probiotic viability and major technological challenge faced during formulation of probiotic ice cream. Keywords used for data searched included dairy-based functional foods, ice cream variants, probiotic ice cream, factors affecting probiotic viability and health benefits of probiotic ice cream.

Retention of probiotic viability at a level of >10⁶ cfu/ml is a prerequisite for functional probiotic ice creams. Functional probiotic ice cream could have been produced with the modification of basic mix and modulating technological parameters during processing and freezing. Functionality can be further enhanced with the inclusion of certain nutraceutical components such as prebiotics, antioxidant, phenolic compounds and dietary fibres. Based upon reviewed literature, suggested method for the manufacture of functional probiotic ice cream involved freezing of a probiotic ice cream mix obtained by blending 10% probiotic fermented milk with 90% non-fermented plain ice cream mix for higher probiotic viability. Probiotic ice cream with functional features, comparable with traditional ice cream in terms of technological and sensory properties could be produced and can crop up as a novel functional food.

Probiotic ice cream with functional features may attract food manufacturers to cater health-conscious consumers.

Due to herbs and plants’ therapeutic properties and simplicity of availability in nature, humans have used them to treat a variety of maladies and diseases since ancient times. Later, as technology advanced, these plants and herbs gained significant relevance in some industries due to their suitable chemical composition, abundant availability and ease of access. Aegle marmelos is a species of plant that may be found in nature. Yet, little or very little literature was located on the coloration behavior of this plant’s leaves. This study aims to focus on the effect of different parameters on the extraction of colorant from Aegle marmelos leaves.

Some factors that affected on the extraction processes were examined and found to have significant impacts on the textile dyeing such as the initial dye concentration, extracted temperature, extracted bath pH and extracted time were all changed to see how they affected color extraction. The authors report a direct comparison between three heating methods, namely, microwave irradiation (MWI), ultrasonic waves (USW) and conventional heating (CH). The two kinetic models have been designed (pseudo-first and pseudo-second orders) in the context of these experiments to investigate the mechanism of the dyeing processes for fabrics under study. Also, the experimental data were analyzed according to the Langmuir and Freundlich isotherms.

From the result, it was discovered these characteristics were found to have a substantial effect on extraction efficiency. Temperature 90°C and 80°C when using CH and USW, respectively, while at 90% watt when using MWI, period 120 min when using CH as well as USW waves, while 40 min when using MWI, and pH 4, 5 and 10 for polyamide, wool and cotton, respectively, were the optimal extraction conditions. Also, the authors can say that wool gives a higher absorption than the other fabric. Additionally, MWI provided the best color strength (K/S) value, and homogeneity, at low temperatures reducing the energy and time consumed. The coloring follows the order: MWI > USW > CH. The adsorption isotherm of wool could be well fitted by Freundlich isotherm when applying CH and USW as a heating source, while it is well fitted by the Langmuir equation in the case of MWI. In the study, it was observed that the pseudo-first-order kinetic model fits better the experimental results of CH with a constant rate K₁ = −0.000171417 mg/g.min, while the pseudo-second-order kinetic model fits better the experimental results of absorption of both MWI (K2 = 38.14022572 mg/g.min) and USW (K₂ = 12.45343554 mg/g.min).

There is no research limitation for this work. Dye was extracted from Aegle marmelos leaves by applying three different heating sources (MWI, ultrasonic waves [USWW] and CH).

This work has practical applications for the textile industry. It is concluded that using Aegle marmelose leaves can be a possible alternative to extract dye from natural resource by applying new technology to save energy and time and can make the process greener.

Socially, it has a good impact on the ecosystem and global community because the extracted dye does not contain any carcinogenic materials.

The work is original and contains value-added products for the textile industry and other confederate fields.

The purpose of this study was to determine the influence of environmental pH on production of biofilms and virulence genes expression in Pseudomonas aeruginosa.

Among 303 clinical and environmental samples 109 (61 + 48) isolates were identified as clinical and environmental P. aeruginosa isolates, respectively. Clinical samples were obtained from patients in the Al-Yarmouk hospital in Baghdad city, Iraq. Waste water from Al-Yarmouk hospital was used from site before treatment unit to collect environmental samples. The ability of producing biofilm at various pH levels was examined by microtiter plate and the prevalence of Alg D, Psl A and Pel A was determined by quantitative real time-polymerase chain reaction (qRT-PCR).

This study showed that the ability of clinical and environmental isolates to biofilm development was observed in 86.9% and 85.42% of clinical and environmental isolates, respectively. As well as, the environmental P. aeruginosa isolates showed the highest biofilm production at pH 7. Clinical isolates showed the highest genes expression of Alg D, Psl A and Pel A as compared to environmental isolates with pH change. In general, both clinical and environmental isolates formed biofilm and carried AlgD, PslA and PelA genes. Also, alkaline pH was favored for biofilm production.

There are very few studies done to find out the influence of environmental pH on production of biofilms and virulence genes expression in Pseudomonas aeruginosa. This study is unique as it has highlighted the influence of environmental pH on the ability of clinical and environmental isolates to biofilm development and genes expression.

This study aims to investigation of the guar gum-manganese dioxide (GG/MnO₂) nanocomposite (NC) synthesized using an environment-friendly method and the degradation of reactive yellow (RY 145) dye in the UV system.

Characterization of the GG/MnO₂ NCs were conducted using field emission scanning electron microscopy, X-ray diffraction and Fourier-transform infrared spectroscopy. Experiments were conducted using a 1 L glass reactor coupled with Ultraviolet (UV-C) blue light bulb of wavelength 250 nm and power of 8 W.

The NC (2.25 g/L) displayed high RY 145 dye degradation (81%) with 10 mg/L of concentration at pH 3. The coefficient of determination (R² 0.99) also depicted that the model fits the experimental data. The analysis of variance (ANOVA) showed that the F-values of 464.75, 276.04 and 5.15 are related to the dose of GG/MnO₂ NCs, initial concentration of RY 145 dye and solution pH, respectively.

The GG/MnO₂ NCs followed by photo oxidation process (UV-process) could be used to degrade the RY 145 dye from synthetic wastewater.

There are two main innovations. One is that the novel process is performed successfully for RY 145 dye degradation. The other is that the optimized conditions are obtained by Box–Behnken design. Also, the effects of different variables on the RY 145 dye removal efficiency were investigated.

The purpose of the study was to produce a healthier, convenient and traditional ready-to-eat (RTE) snack option with increased nutritional value, using spent hen meat, dietary fibre (DF) and simple technological methods. The product was designed to be stable without refrigeration and be easily adoptable by local self-help groups, rural women and youth and entrepreneurs in urban and semi-urban areas.

Conventional binder used for making snacks, i.e. rice flour was partially replaced by different sources of antioxidant DFs, i.e. oat flour (T₁ – 10%), finger millet flour (T₂ – 5%) and amaranth flour (T₃ –15%) to prepare spent hen snack sticks (SHSS). The snacks were then packaged in low density polyethylene (LDPE) pouches and evaluated for their storage stability at ambient temperature for a period of 35 days. Their physico-chemical, sensory and microbiological quality was evaluated at a regular interval of 7 days. The proximate composition of developed SHSS was compared to commercially available snack products (chakli/murukku – snacks without meat).

The fibre-enriched SHSS showed significant improvement in nutritive value, as they contained more fibre (p = 0.001) and protein (p = 0.029) than control SHSS. When compared to commercially available snack product SHSS showed three-fold significant increase in protein (p = 0.000) and ash content (p = 0.001) and only 11%–12% total fat as compared to 31% fat in the market-available product. The most acceptable treatment in terms of overall sensory quality and nutritional aspects was T₃; however, T₂ was more shelf-stable during the storage period. The study showed that fibre-enriched snacks can be stored at ambient temperature for up to 35 days without substantial loss in physico-chemical, sensory and microbial quality. Hence, substituting rice flour with DFs can lead to the development of products with better sensory attributes and improved functionality.

The simplicity of the product in terms of composition, machinery and low production costs makes it an easily adoptable one by small-scale entrepreneurs, especially those belonging to semi-urban areas.

Incorporation of spent hen meat, a relatively cheap but abundant source of protein, in RTE products can serve as an effective way to alleviate protein malnutrition, whereas addition of fibre further improves the functionality of the product. The methodology can be easily taken up by small-scale entrepreneurs and create a market for snack-based functional meat products.

This study aims to investigate the role of aluminium (Al) in marine environment and the corrosion mechanism of galvalume coatings by conducting accelerated experiments and data analysis.

Samples were subjected to accelerated corrosion for 136 days via salt spray tests to simulate the natural conditions of marine environment and consequently accelerate the experiments. Subsequently, the samples were examined using various test methods, such as EDS, scanning electron microscopy (SEM), X-ray diffraction (XRD) and electrochemical impedance spectroscopy (EIS), and the obtained data were analysed.

Galvalume coatings comprised interdigitated zinc (Zn)-rich and dendritic Al-rich phases. Corrosion was observed to begin with a Zn-rich phase. The primary components of the corrosion product film were Al₂O₃ and Zn₅(OH)₈Cl₂·H₂O. It was confirmed that the role of Al was to form a dense protective film, thereby successfully blocking the entry of corrosive media and protecting the iron substrate.

This study provides a clearer understanding of the corrosion mechanism and kinetics of galvalume coatings in a simulated marine environment. In addition, the role of Al, which is rarely mentioned in the literature, was investigated.