Search results

Steer-by-wire (SBW) system mainly relies on sensors, controllers and motors to replace the traditionally mechanical transmission mechanism to realize steering functions. However, the sensors in the SBW system are particularly vulnerable to external influences, which can cause systemic faults, leading to poor steering performance and even system instability. Therefore, this paper aims to adopt a fault-tolerant control method to solve the safety problem of the SBW system caused by sensors failure.

This paper proposes an active fault-tolerant control framework to deal with sensors failure in the SBW system by hierarchically introducing fault observer, fault estimator, fault reconstructor. Firstly, the fault observer is used to obtain the observation output of the SBW system and then obtain the residual between the observation output and the SBW system output. And then judge whether the SBW system fails according to the residual. Secondly, dependent on the residual obtained by the fault observer, a fault estimator is designed using bounded real lemma and regional pole configuration to estimate the amplitude and time-varying characteristics of the faulty sensor. Eventually, a fault reconstructor is designed based on the estimation value of sensors fault obtained by the fault estimator and SBW system output to tolerate the faulty sensor.

The numerical analysis shows that the fault observer can be rapidly activated to detect the fault while the sensors fault occurs. Moreover, the estimation accuracy of the fault estimator can reach to 98%, and the fault reconstructor can make the faulty SBW system to retain the steering characteristics, comparing to those of the fault-free SBW system. In addition, it was verified for the feasibility and effectiveness of the proposed control framework.

As the SBW fault diagnosis and fault-tolerant control in this paper only carry out numerical simulation research on sensors faults in matrix and laboratory/Simulink, the subsequent hardware in the loop test is needed for further verification.

Aiming at the SBW system with parameter perturbation and sensors failure, this paper proposes an active fault-tolerant control framework, which integrates fault observer, fault estimator and fault reconstructor so that the steering performance of SBW system with sensors faults is basically consistent with that of the fault-free SBW system.

The first step toward developing an automated construction workers performance monitoring system is to initially establish a complete and competent activity recognition solution, which is still lacking. This study aims to propose a novel approach of using labor physiological data collected through wearable sensors as means of remote and automatic activity recognition.

A pilot study is conducted against three pre-fabrication stone construction workers throughout three full working shifts to test the ability of automatically recognizing the type of activities they perform in-site through their lively measured physiological signals (i.e. blood volume pulse, respiration rate, heart rate, galvanic skin response and skin temperature). The physiological data are broadcasted from wearable sensors to a tablet application developed for this particular purpose, and are therefore used to train and assess the performance of various machine-learning classifiers.

A promising result of up to 88% accuracy level for activity recognition was achieved by using an artificial neural network classifier. Nonetheless, special care needs to be taken for some activities that evoke similar physiological patterns. It is expected that blending this method with other currently developed camera-based or kinetic-based methods would yield higher activity recognition accuracy levels.

The proposed method complements previously proposed labor tracking methods that focused on monitoring labor trajectories and postures, by using additional rich source of information from labors physiology, for real-time and remote activity recognition. Ultimately, this paves for an automated and comprehensive solution with which construction managers could monitor, control and collect rich real-time data about workers performance remotely.

The purpose of this paper is to develop a highly miniaturized wireless inertial sensor system based on a novel 3D packaging technique using a flexible printed circuit (FPC). The device is very suitable for wearable applications in which small size and lightweight are required such as body area network, medical, sports and entertainment applications.

Modern wireless inertial measurement units are typically implemented on a rigid 2D printed circuit board (PCB). The design concept presented here is based around the use of a novel planar, six‐faceted, crucifix or cross‐shaped FPC instead of a rigid PCB. A number of specific functional blocks (such as microelectromechanical systems gyroscope and accelerometer sensors, microcontroller (MCU), radio transceiver, antenna, etc.) are first assigned to each of the six faces which are each 1 cm² in area. The FPC cross is then developed into a 1 cm³, 3D configuration by folding the cross at each of five bend planes. The result is a low‐volume and lightweight, 1 cm³ wireless inertial sensor that can sense and send motion sensed data wirelessly to a base station. The wireless sensor device has been designed for low power operation both at the hardware and software levels. At the base station side, a radio receiver is connected to another MCU unit, which sends received data to a personal computer (PC) and graphical user interface. The industrial, scientific and medical band (2.45 GHz) is used to achieve half duplex communication between the two sides.

A complete wireless sensor system has been realized in a 3D cube form factor using an FPC. The packaging technique employed during the work is shown to be efficient in fabricating the final cubic system and resulted in a significant saving in the final size and weight of the system. A number of design issues are identified regarding the use of FPC for implementing the 3D structure and the chosen solutions are shown to be successful in dealing with these issues.

Currently, a limitation of the system is the need for an external battery to power the sensor system. A second phase of development would be required to investigate the possibility of the integration of a battery and charging system within the cube structure. In addition, the use of flexible substrate imposes a number of restrictions in terms of the ease of manufacturability of the final system due to the requirement of the required folding step.

The small size and weight of the developed system is found to be extremely useful in different deployments. It would be useful to further explore the system performance in different application scenarios such as wearable motion tracking applications. In terms of manufacturability, component placement needs to be carefully considered, ensuring that there is sufficient distance between the components, bend planes and board edges and this leads to a slightly reduced usable area on the printed circuit.

This paper provides a novel and useful method for realizing a wireless inertial sensor system in a 3D package. The value of the chosen approach is that a significant reduction in the required system volume is achieved. In particular, a 78.5 per cent saving in volume is obtained in decreasing the module size from a 25 to a 15 mm³ size.

Ride comfort is one of the important factors affecting passenger health. Therefore, the elevator industry usually uses the International Organization for Standardization (ISO) 18738-1 standard to evaluate elevator ride quality and optimize elevator design. However, this method has certain limitations in its evaluation of comfort due to the problem of boundary division. The ISO 2631-4 standard is used as a general method of comfort evaluation in the current rail transit system, but it has not been applied in the elevator industry. In order to explore the difference and connection between the two standards, the author aims to conduct a detailed analysis on this.

Based on the elevator internet, a large amount of measured data of normal and abnormal vibration of elevator car were collected and analyzed and preprocessed; based on ISO 18738-1:2012 standard and ISO 2631-4:2001 standard, the differences of ride comfort assessment methods in the two standards were analyzed, and the ride comfort assessment study of elevator under normal and abnormal vibration conditions was carried out.

The experimental results show that the comfort assessment results of ISO 2631-4:2001 standard and ISO18738-1:2012 standard are consistent under two vibration conditions. At the same time, ISO 2631-4:2001 can not only provide a more accurate quantitative description of comfort, but also roughly determine the comfort interval of each vibration, which can provide theoretical reference for elevator vibration classification and car comfort design.

The authors designed an Internet of Things (IOT)-based elevator vibration signal acquisition method to address the shortcomings of the previous elevator ride comfort assessment methods, which can realize the dynamic assessment of elevator ride comfort; by comparing the assessment results of elevator ride comfort under normal vibration and abnormal vibration, the feasibility of ISO 2631-4:2001 for elevator ride comfort assessment was fully verified. In addition, the experimental results also give the influence of abnormal vibration on elevator riding comfort under the stages of start-stop, uniform speed, acceleration and deceleration, which can provide theoretical support for elevator vibration suppression and comfort transformation.