Search results

The purpose of this paper is to review possibilities of implementing ceramic additive manufacturing (AM) into electronic device production, which can enable great new possibilities.

A short introduction into additive techniques is included, as well as primary characterization of structuring capabilities, dielectric performance and applicability in the electronic manufacturing process.

Ceramic stereolithography (SLA) is suitable for microchannel manufacturing, even using a relatively inexpensive system. This method is suitable for implementation into the electronic manufacturing process; however, a search for better materials is desired, especially for improved dielectric parameters, lowered sintering temperature and decreased porosity.

Relatively inexpensive ceramic SLA, which is now available, could make ceramic electronics, currently restricted to specific applications, more available.

Ceramic AM is in the beginning phase of implementation in electronic technology, and only a few reports are currently available, the most significant of which is mentioned in this paper.

The purpose of this paper is to present the properties of thick-film resistors made of novel pastes prepared from glass and graphite.

Graphite-based resistors were made of thick-film pastes with different graphite-to-glass mass fraction were prepared and examined. Sheet resistance, temperature coefficient of resistance, impact of humidity and short-term overload were investigated. The properties of the layers fired in atmospheres of air at 550°C and nitrogen at 875°C were compared.

Graphite-based resistors with various graphite-to-glass ratios made possible to obtain a wide range of sheet resistance from single O/square to few kO/square. These values were dependent on firing atmosphere, paste composition and the number of screen-printed layers. The samples made of paste with 1:1 graphite-to-glass ratio exhibited the temperature coefficient of resistance of about −1,000 ppm/°C, almost independently on the firing atmosphere and presence of a top coating. The resistors fired in the air after coating with overglaze, exhibited significantly lower sheet resistance, reduced impact of humidity and improved power capabilities.

In this paper, graphite-based resistors for applications in typical high-temperature cermet thick-film circuits were presented, whereas typical graphite-based resistors were fabricated in polymer thick-film technology. Owing to very low cost of the graphite, the material is suitable for low-power passive circuits, where components are not subjected into high temperature, above the typical temperature of operation of standard electronic components.

Intervention evaluations have not always accounted for long-term implementation of interventions. The purpose of this paper is to explore implementation of a primary care intervention during the lifespan of the trial and beyond.

Eight general practices participated in the trial (four control and four intervention). In-depth interviews (with nine GPs and four practices nurses who delivered the intervention) and observation methods were employed. Thematic analysis was utilized and Normalization Process Theory (NPT) constructs were compared with emergent themes.

Macro-level policy imperatives shaped practice priorities which resulted in the “whole system” new intervention not being perceived to be sustainable. Continued routinization of the intervention into usual care beyond the lifespan of the funded study was dependent on individualized monitoring and taking forward tacit knowledge.

The authors discuss the implications of these findings for sociological theories of implementation and understanding outcomes of research led complex interventions.

The study describes the complex interplay between macro processes and individual situated practices and contributes to understanding if, how, and why interventions are sustained beyond initial “research push”. The value of the study lies in describing the conditions and potential consequences of long-term implementation, which might be translated to other contexts.

At the outbreak of the COVID-19 pandemic, the absence of pharmaceutical agents meant that policy institutions had to intervene by providing nonpharmaceutical interventions (NPIs). To satisfy this need, the World Health Organization (WHO) issued policy guidelines, such as NPIs, and the government of Pakistan released its own policy document that included social distancing (SD) as a containment measure. This study explores the policy actors and their role in implementing SD as an NPI in the context of the COVID-19 pandemic.

The study adopted the constructs of Normalization Process Theory (NPT) to explore the implementation of SD as a complex and novel healthcare intervention under a qualitative study design. Data were collected through document analysis and interviews, and analysed under framework analysis protocols.

The intervention actors (IAs), including healthcare providers, district management agents, and staff from other departments, were active in implementation in the local context. It was observed that healthcare providers integrated SD into their professional lives through a higher level of collective action and reflexive monitoring. However, the results suggest that more coherence and cognitive participation are required for integration.

This novel research offers original and exclusive scenario narratives that satisfy the recent calls of the neo-implementation paradigm, and provides suggestions for managing the implementation impediments during the pandemic. The paper fills the implementation literature gap by exploring the normalisation process and designing a contextual framework for developing countries to implement guidelines for pandemics and healthcare crises.

The objective of the study was to assess consumer exposure to warmed-over flavour, their eating habits with respect to pre-cooked stored meats, awareness of antioxidants and attitudes towards the use of natural antioxidants as preservatives in meat and meat products.

A total of 238 Check-All-That-Apply (CATA) design questionnaires were used to gather information from the University of Fort Hare community in the Eastern Cape province of South Africa.

The majority of the respondents had been exposed to warmed-over flavour before. More than half of the respondents did not know about antioxidants. Respondents were in support of the use of natural antioxidants in meat and meat products.

The study mainly captured consumer habits based on living arrangements. Age influence could not be extrapolated due to the nature of the population, which was being studied. The population was limited to the University community, which is mainly made up of not so widely spread age groups and more or less similar levels of education. As a result, the findings and conclusions may not be a true reflection of the general public consumers in terms of age, level of education and employment status.

This research presents an original insight into consumer habits concerning the purchasing and storage of pre-cooked meat and meat products. The study revealed that most consumers nowadays prefer ready-to-eat or pre-cooked meat and meat products due to convenience. The warmed-over flavour is common in pre-cooked meats. The findings suggests that the meat industry has to improve the shelf-life of pre-cooked foods such that warmed-over flavour development is delayed to fit into the current consumer habits. In recent years there has been a growing interest in the use of natural antioxidants to improve shelf-life of muscle foods. However, there is a dearth of information on consumer attitudes towards the use of natural antioxidants as preservatives. This study reveals that consumers are willing to try products formulated using natural antioxidants.