Search results

The objective of this research is to develop a method for designing customised pressure garments that can be more accurately applied to a burn wound area. The method includes the use of a 3D digital image of the wounded body part obtained by a body scanner and the development of a 3D pressure garment model and a 2D pattern. The scanned data contain detailed information that cannot be feasibly obtained by manual measurements, such as body curvature. The model parameters include the pressure to be exerted, pressure garment fabric properties and radius of curvature of the cross-sections of scanned body parts. By using a 3D pressure garment model, a 2D garment pattern is developed, and then, a pressure garment is constructed by using the pattern. The technique has been experimentally verified and customised pressure garments are made for a number of volunteer subjects. The customised pressure garments made for the subjects exert pressures close to the design pressure, but vary along the circumference of a given cross-section. The customised pressure garments constructed by using the developed method have shown a more accurate fit to uniformly exert the design pressure onto the whole of the wounded area.

This paper reports a pressure distribution model that will predict the pressure applied by a pressure garment onto a wounded body segment which could facilitate the production of custom made pressure garments. The model is generated by using the 3D data of the wounded body segment of a patient which are obtained by a non-intrusive non-contact measurement system. The circumference of the body segment is calculated from scanned digital data. Then, a circumference reduction factor is calculated to determine the circumference of the pressure garment in order to apply the design pressure by using a specific fabric with an experimentally determined modulus of elasticity in the circumferential direction. Then, the radius of curvature for each data point in a given layer is calculated and the pressure applied is obtained. Finally, a 3D pressure distribution model for the whole wounded part is constructed by stacking the pressure maps of adjacent layers. The model is verified through a comparison with the actual pressure measured by using custom made pressure garments and volunteer subjects. The comparison shows reasonable agreement. The model enables garment manufacturers/therapists to evaluate the effectiveness of a custom designed pressure garment before it is manufactured and eliminates the need for in-situ pressure measurements.

Examines the thirteenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

Discusses the 6th ITCRR, its breadth of textile and clothing research activity, plus the encouragement given to workers in this field and its related areas. States that, within the newer research areas under the microscope of the community involved, technical textiles focuses on new, ‘smart’ garments and the initiatives in this field in both the UK and the international community at large. Covers this subject at length.

Examines the fourteenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

Examines the fifteenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

Examines the fifthteenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

Looks at the eighth published year of the ITCRR and the research, from far and near, involved in this. Muses on the fact that, though all the usual processes are to the fore, the downside part of the industry is garment making which is the least developed side. Posits that the manufacture of clothing needs to become more technologically advanced as does retailing. Closes by emphasising support for the community in all its efforts.

The aim of this paper was to explore the use of objective fabric parameters in 3D virtual garment simulation.

Two methods (fabric assurance by simple testing and Browzwear's fabric testing kit) of obtaining objective fabric measurements and the derived parameters for virtual garment simulation were studied. Three parameters (extension, shear and bend) were investigated to establish whether the selected virtual software derived comparable parameters from the objective fabric measurements.

It was found that the conversion from the objective fabric measurement data to the required parameters for virtual simulation varied significantly. Manual analysis of the objective measurements showed the two test methods to be comparable for extension and shear parameters; However, some adjustment to the test method was required. The third parameter to be investigated (bending rigidity) concluded that the test methods and results obtained from the two different apparatus were not comparable and recommended further experimentation using a different testing technique.

Future research should be conducted on a larger variety of fabrics ensuring comparable loads are used in the testing of the extensibility parameters. An expansion of this preliminary study should give more conclusive evidence of the trends observed.

Objective measurement of extension, shear and bend properties was investigated in relation to the derived parameters for a selected virtual simulation package. An understanding of such parameters will aid the general industry in adapting 3D virtual garment simulation as part of the standard product development process, resulting in a significantly shorter product development cycle.

The purpose of this paper is to present a new collaborative design-based method for designing customized garments, aimed at the physically disabled people with scoliosis.

The proposed method is based on the virtual human model created using a 3D body scanner, permitting to simulate the consumer’s morphological shape with atypical physical deformations. Next, customized 2D and 3D virtual garment prototyping tools will be used to create products through interactions between the consumer, designer and pattern maker. The general principle of the proposed design method is based on the following sequence: design-display-evaluation-adjustment. After running the sequence for a number of times, the final design solution, which will be approved by both the designer and consumer, can be easily identified.

Design knowledge, which is already applied to normal body shapes successfully can be applied to 3D garment design using the concept which is based on collaborative design. Through this process, the classical 2D garment design knowledge, especially 2D patterns and design rules, can be modified and applied according to a normalized virtual garment sensory evaluation procedure quantitatively. This evaluation procedure, interactively performed by the designer and consumer, can permit to adapt the finished product to disabled people afflicted with severe scoliosis. The proposed method is also validated to be more advanced compared to 2D-to-3D virtual CAD design method, especially for atypical morphologies.

As a co-design method, 3D virtual draping and sensory evaluation can fully satisfy the interaction between the garment design technical space and perceptual space of the finished garments ensuring desired 3D garment fit effect by adjustment of technical parameters. 3D scanning technology is used to generate a complete digitalized 3D human model, permitting to extract the main features of body shapes without accurate measurements. As a knowledge-based design process, both the fashion design knowledge and the pattern making knowledge will be extracted to provide inspirations and references. Successful design solutions will be incorporated into the fashion design knowledge base in order to generate new design rules and enhance professional design knowledge.