To read this content please select one of the options below:

Additive manufacturing using fine wire-based laser metal deposition

Muhammad Omar Shaikh (Institute of Medical Science and Technology, National Sun Yat-sen University, Kaohsiung, Taiwan)
Ching-Chia Chen (Department of Mechanical Engineering, Southern Taiwan University of Science and Technology, Tainan, Taiwan)
Hua-Cheng Chiang (Department of Mechanical Engineering, Southern Taiwan University of Science and Technology, Tainan, Taiwan)
Ji-Rong Chen (Department of Mechanical Engineering, Southern Taiwan University of Science and Technology, Tainan, Taiwan)
Yi-Chin Chou (Kuang Tai Metal Industrial Co. Ltd., Kaohsiung, Taiwan)
Tsung-Yuan Kuo (Department of Mechanical Engineering, Southern Taiwan University of Science and Technology, Tainan, Taiwan)
Kei Ameyama (Department of Mechanical Engineering, School of Science and Engineering, College of Science and Engineering Graduate, Ritsumeikan University, Kusatsu, Japan)
Cheng-Hsin Chuang (Institute of Medical Science and Technology, National Sun Yat-sen University, Kaohsiung, Taiwan)

Rapid Prototyping Journal

ISSN: 1355-2546

Article publication date: 6 December 2019

Issue publication date: 3 April 2020

830

Abstract

Purpose

Using wire as feedstock has several advantages for additive manufacturing (AM) of metal components, which include high deposition rates, efficient material use and low material costs. While the feasibility of wire-feed AM has been demonstrated, the accuracy and surface finish of the produced parts is generally lower than those obtained using powder-bed/-feed AM. The purpose of this study was to develop and investigate the feasibility of a fine wire-based laser metal deposition (FW-LMD) process for producing high-precision metal components with improved resolution, dimensional accuracy and surface finish.

Design/methodology/approach

The proposed FW-LMD AM process uses a fine stainless steel wire with a diameter of 100 µm as the additive material and a pulsed Nd:YAG laser as the heat source. The pulsed laser beam generates a melt pool on the substrate into which the fine wire is fed, and upon moving the X–Y stage, a single-pass weld bead is created during solidification that can be laterally and vertically stacked to create a 3D metal component. Process parameters including laser power, pulse duration and stage speed were optimized for the single-pass weld bead. The effect of lateral overlap was studied to ensure low surface roughness of the first layer onto which subsequent layers can be deposited. Multi-layer deposition was also performed and the resulting cross-sectional morphology, microhardness, phase formation, grain growth and tensile strength have been investigated.

Findings

An optimized lateral overlap of about 60-70% results in an average surface roughness of 8-16 µm along all printed directions of the X–Y stage. The single-layer thickness and dimensional accuracy of the proposed FW-LMD process was about 40-80 µm and ±30 µm, respectively. A dense cross-sectional morphology was observed for the multilayer stacking without any visible voids, pores or defects present between the layers. X-ray diffraction confirmed a majority austenite phase with small ferrite phase formation that occurs at the junction of the vertically stacked beads, as confirmed by the electron backscatter diffraction (EBSD) analysis. Tensile tests were performed and an ultimate tensile strength of about 700-750 MPa was observed for all samples. Furthermore, multilayer printing of different shapes with improved surface finish and thin-walled and inclined metal structures with a minimum achievable resolution of about 500 µm was presented.

Originality/value

To the best of the authors’ knowledge, this is the first study to report a directed energy deposition process using a fine metal wire with a diameter of 100 µm and can be a possible solution to improving surface finish and reducing the “stair-stepping” effect that is generally observed for wires with a larger diameter. The AM process proposed in this study can be an attractive alternative for 3D printing of high-precision metal components and can find application for rapid prototyping in a range of industries such as medical and automotive, among others.

Keywords

Acknowledgements

The authors are grateful for the financial support provided by Kuang Tai Metal Industrial Co., Ltd. for this research work.

Citation

Shaikh, M.O., Chen, C.-C., Chiang, H.-C., Chen, J.-R., Chou, Y.-C., Kuo, T.-Y., Ameyama, K. and Chuang, C.-H. (2020), "Additive manufacturing using fine wire-based laser metal deposition", Rapid Prototyping Journal, Vol. 26 No. 3, pp. 473-483. https://doi.org/10.1108/RPJ-04-2019-0110

Publisher

:

Emerald Publishing Limited

Copyright © 2019, Emerald Publishing Limited

Related articles