Search results

The effects of electrode types on the mechanical properties of weldments produced from three steel samples made locally in Nigeria have been investigated. Oerlikon, Santan, Power Master and Magnum electrode samples were separately used to join Homus, Universal and Spanish steel samples. The chemical compositions of the steel samples, electrodes core and coating were obtained using spectrometer before using them for the research. Mechanical properties of the weldment produced were determined and compared to the unwelded samples. This was done in order to provide information on which combination of steel and electrode type will produce weldment with optimum mechanical properties. Oerlikon electrode produces weldments with optimum tensile strength of 508.25 N/mm² and impact energy of 152.76J for Homus Steel, it also produced highest tensile strength of 449.92 N/mm² and impact energy of 103.042J for Spanish Steels while Power Master Electrode produced weldment with highest tensile strength of 482.96N/mm² and impact energy of 137.033J for Universal Steel. The results show that single electrode type cannot produce weldment with highest properties for all the selected steel samples.

Chicken feather particles reinforced rubber seed oil based polyurethane composites were produced and the physico-mechanical and microstructural analyses were studied. Casting method was used to produce the composites with varied weights of Chicken feather particles from 5 to 25wt% in steps of 5 wt%. The composites produced were analyzed for hardness, impact strength, tensile strength, density and water absorption properties according to ASTM standards. The density and impact strength were observed to decrease with increase in percentage weight of the chicken feather particles and this was attributed to the fact that the feathers have lower density than RSO-Polyurethane. Tensile strength and hardness of the composites were found to decrease at the intial stage (0 to 10 wt%) and later started to increase with percentage increase(15 to 25 wt%) of reinforment added. The microstructure reveals that there was a reasonable uniform distribution and bonding of chicken feather particles in the RSO-Polyurethane matrix.

The purpose of this paper is to evaluate experimentally the influence of different surface roughness of the contacting disc on tribological performance of the non-asbestos brake friction material (BFM).

Taguchi method was applied to design an experiment using three different discs of gray cast iron with different surface roughness, which is measured using optical profilometer. These discs were subjected to sliding against pins prepared with the developed non-asbestos BFM, using pin on disc friction and wear monitor.

The experimental results shows that the disc 2 (Ra = 3.77 µm) gives wear of 22.78 µm and coefficient of friction of 0.462, which is recommended for extreme brake performance. Analysis of Taguchi design revealed that the disc surface was most significant parameter among the parameters under study.

During braking, continuous sliding between the BFM and brake disc or drum not only results into wear of BFM but also changes the surface finish of the brake drum or disc. This leads to variation in surface topography of the drum or disc surface with application of brakes, which further affects the characteristics of the BFM.

The tribological performance of BFM depends upon the topography of the surface on which it was sliding. To get best performance of the non-asbestos friction materials, disc having moderate surface finish is recommended. Scanning electron microscope micrographs had shown the different plateaus formed and energy-dispersive X-ray spectroscopy spectra identified presence of different chemical elements prior to sliding of the pins surface over different discs surface topography.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2020-0120/

Aluminium metal matrix composite (AMMC) is most popular in various industrial applications such as aerospace, automobile, marine, sports and many others. In common practice, silicon carbide, aluminum oxides, magnesium oxide, graphene and carbon nano tubes are the major reinforcing elements to prepare the AMMC. The purpose of this paper is to develop AMMCs reinforce with eggshell (ES) and rice husk ash (RHA).

Stir casting process is used for preparation of AMMC. From past few years, more emphasis is given to prepare the AMMCs using agro waste such as rice husk and/or ES as reinforcing materials. In this method, after the Al-matrix material is melted; it is stirred vigorously to form vortex at the surface of the melt, and the reinforcement material is then introduced at the side of the vortex. Stir casting process is a vortex and vigorous method to prepare the AMMCs. First, aluminum alloy (AA3105) is melted in the furnace when metal is in semisolid form. Reinforcement, i.e. ES and RHA are preheated at temperature 220°C and 260°C, respectively.

The result of AMMC shows that the tensile strength and hardness increased by using 22.41% and 45.5%, respectively, at 4.75 Wt.% each reinforcement, i.e. ES and RHA, and 1% Cr. The toughness and ductility of metal matrix composite (MMCs) have decreased up to 23.31% and 19.23% respectively by using 1% Cr, 4.75 wt. % ES and by 4.75 wt. % RHA of composite material.

In this work, Cr, waste ES and RHA have been used to develop green MMC to support the green revolution as promoted/suggested by United Nations, thus reducing the environmental pollution.

The purpose of this study to find an alternate method to minimize waste i.e., eggshell and rice husk ash. In this paper, eggshell (ES) and rice husk ash (RHA) particles are used as reinforcements for examining their effect on the coefficient of thermal expansion (CTE), grain size (GS) and corrosion behavior for developed composite material.

In this investigation, 5 Wt.% each of ES and RHA reinforcement particles have been introduced. To investigate the microstructures of the developed composite material, scanning electron microscope was used. Physical and mechanical properties of composite material are tensile strength and hardness that have been examined.

The result of this paper shows that number of grains per square inch for composition Al/5% ES/5% RHA composite was found to be 1,243. Minimum value of the volume CTE was found to be 6.67 × 10–6/°C for Al/5% ES/5% RHA composite. The distribution of hard phases of ES particles in metal matrix is responsible for improvements in tensile strength and hardness. These findings demonstrated that using carbonized ES as reinforcement provides superior mechanical and physical properties than using uncarbonized ES particles.

There are several articles examining the impact of varying Wt.% of carbonized ES and rice husk reinforcement on the microstructures and mechanical characteristics of metal composites. CTE, GS and corrosion behavior are among of the features that are examined in this paper.

The purpose of this paper is to develop strategies for potential environmental impacts as a result of institutional arrangement and development of oil palm downstream industry both regionally and nationally.

The research location is in the areas potential for oil palm plantation development, either by plasma through BUMN and BUMS or self-supporting by the society. The research location will be divided into two parts, namely, the land area and the coastal area. The Riau land areas are Regency of Kampar, Rokan Hulu, and Kuantan Singingi, while Riau coastal areas are Regency of Pelalawan, Siak, Bengkalis, Indragiri Hilir, Indragiri Hulu and Rokan Hilir. Both research areas have different productivity due to the different soil fertility levels. The sustainability level of oil palm plantation from the socio-economic and environmental aspects is analyzed using the multi-dimensional scaling approach modified into Rapid Appraisal-Index Sustainability of Palm Oil Management.

In Riau Province, the development of oil palm is quite rapid. This is reasonable for several reasons which include the following supporting factors: the geographical condition of the Riau region is very supportive; the high demand for palm oil derivative products; the existence of market guarantee for oil palm farmers; the higher income oil palm generates than other plantation crops; and the relatively flat area. Most of the problems faced by oil palm farmers are the use of less good seeds, the length of the fruit laying at the location of the plantation, the inadequate production road, the relatively far distance to palm oil mill (POM) (National Agency of Drug and Food Control), the tendency of determining the unilateral revenue of the POM, the collectively measurement of revenue and the general revenue information. The development of oil palm plantations has created an entrepreneurial capability for farmers who are able to capture business opportunities in the agricultural sector, especially the plantation sub-sector.

The originality of this paper shows the comprehensively control strategy, potential of environmental impact and palm oil plantation. The method used for data collection was rapid rural appraisal method because accurate information is needed in a limited time as it relates to decisions related to village development that must be taken immediately. The study area was conducted in Riau Province because Riau Province is one of the biggest palm oil producers in Indonesia. The study sites will be divided into two, namely, the land area and the coastal area.