Search results

Understanding the performance and flight envelope of a damaged aircraft is a preliminary requirement to recover the aircraft after damage. This paper aims to provide a comprehensive understanding of wing damage effect on airplane performance, local stability, and flying quality of each trim state inside the achievable flight envelope.

This paper demonstrates the use of attainable equilibrium points which are referred as trim states in order to estimate a damaged airplane manoeuvring flight envelope using a numerical computation method.

Wing damaged airplane manoeuvring flight envelope is estimated for different portions of the wing tip loss. Local stability at each trim condition inside the estimated flight envelope is analysed, and also motion flight modes and flying quality sensitivity to the wing damage are explored.

Local stability and flying quality analysis at each trim condition inside the flight envelope which demonstrate the effect of damage provides a criterion to prioritize the choice of trimmed flight condition as motion primitives for the airplane post‐damage flight and safe landing.

This study aims to analyze the two-dimensional ferrofluid flow in porous media. The effects of changes in parameters such as permeability parameter, buoyancy parameter, Reynolds and Prandtl numbers, radiation parameter, velocity slip parameter, energy dissipation parameter and viscosity parameter on the velocity and temperature profile are displayed numerically and graphically.

By using simplification, nonlinear differential equations are converted into ordinary nonlinear equations. Modeling is done in the Cartesian coordinate system. The finite element method (FEM) and the Akbari-Ganji method (AGM) are used to solve the present problem. The finite element model determines each parameter’s effect on the fluid’s velocity and temperature.

The results show that if the viscosity parameter increases, the temperature of the fluid increases, but the velocity of the fluid decreases. As can be seen in the figures, by increasing the permeability parameter, a reduction in velocity and an enhancement in fluid temperature are observed. When the Reynolds number increases, an increase in fluid velocity and temperature is observed. If the speed slip parameter increases, the speed decreases, and as the energy dissipation parameter increases, the temperature also increases.

When considering factors like thermal conductivity and variable viscosity in this context, they can significantly impact velocity slippage conditions. The primary objective of the present study is to assess the influence of thermal conductivity parameters and variable viscosity within a porous medium on ferrofluid behavior. This particular flow configuration is chosen due to the essential role of ferrofluids and their extensive use in engineering, industry and medicine.

The purpose of this paper is to investigate natural convection in a porous wavy-walled enclosure that is including a cylinder cavity in the middle of it and filled with a hybrid nanofluid contains 1-Butanol as the base fluid and MoS₂–Fe₃O₄ hybrid nanoparticles.

The domain of interest is bounded by constant temperature horizontal corrugated surfaces and isothermal vertical flat surfaces. The numerical outputs are explained in the type of isotherms, streamline and average Nusselt number with variations of the Rayleigh number, Hartmann number, nanoparticle shape factor and porosity of the porous medium. For solving the governing equations, the finite element method has been used.

The results show that Nuave is proportional to Rayleigh and nanoparticle shape factor directly as well as it has an inverse relation with Hartmann and porosity. The obtained results reveal that the shape factor parameter has a significant effect on the heat transfer performance, which shows a 55.44% contribution on the average Nusselt number.

As a novelty, to maximize the heat transfer performance in a corrugated walls enclosure, the optimal parameters have intended by using the response surface and Taguchi methods. Additionally, an accurate correlation for the average Nusselt number is developed with sensibly great precision.

The purpose of this study is to determine the extent to which institutional pressures affect supplier and customer collaboration and how collaboration explains green supply chain performance using institutional and stakeholder theories.

The paper builds on empirical evidence gathered from responses of Iranian industrial managers based on a self-administered survey. The hypotheses in the conceptual model are tested using Smart-PLS (partial least square).

The results provide evidence that regulatory requirements and internal motivators, as institutional pressure, enable customer and supplier collaboration. Furthermore, customer collaboration has a positive effect on supplier collaboration and, consequently, positively affects environmental and economic performance. But supplier collaboration is just positively affecting environmental performances and is not effective on economic performance.

The subject is that the study is a questionnaire-based survey, and the validity and reliability of the results are influenced by the respondents' idiosyncrasies. This study provides a comprehensive model of drivers, supply chain collaboration and performance in the context of the industry sector. The study contributes by providing empirical data with a focus on customer and supplier collaboration and their interrelationship in GSCM modelling.

The current paper is one of the new field of research which demonstrate the significance of customer and supplier collaboration with each other to attain green performance. It also contributes to show the effect of institutional pressure on the customer-supplier collaboration that fosters green performance in the supply chain.

Although many studies have been conducted on the nanofluid flow in microtubes, this paper, for the first time, aims to investigate the effects of nanoparticle diameter and concentration on the velocity and temperature fields of turbulent non-Newtonian Carboxymethylcellulose (CMC)/copper oxide (CuO) nanofluid in a three-dimensional microtube. Modeling has been done using low- and high-Reynolds turbulent models. CMC/CuO was modeled using power law non-Newtonian model. The authors obtained interesting results, which can be helpful for engineers and researchers that work on cooling of electronic devices such as LED, VLSI circuits and MEMS, as well as similar devices.

Present numerical simulation was performed with finite volume method. For obtaining higher accuracy in the numerical solving procedure, second-order upwind discretization and SIMPLEC algorithm were used. For all Reynolds numbers and volume fractions, a maximum residual of 10⁻⁶ is considered for saving computer memory usage and the time for the numerical solving procedure.

In constant Reynolds number and by decreasing the diameter of nanoparticles, the convection heat transfer coefficient increases. In Reynolds numbers of 2,500, 4,500 and 6,000, using nanoparticles with the diameter of 25 nm compared with 50 nm causes 0.34 per cent enhancement of convection heat transfer coefficient and Nusselt number. Also, in Reynolds number of 2,500, by increasing the concentration of nanoparticles with the diameter of 25 nm from 0.5 to 1 per cent, the average Nusselt number increases by almost 0.1 per cent. Similarly, In Reynolds numbers of 4,500 and 6,000, the average Nusselt number increases by 1.8 per cent.

The numerical simulation was carried out for three nanoparticle diameters of 25, 50 and 100 nm with three Reynolds numbers of 2,500, 4,500 and 6,000. Constant heat flux is on the channel, and the inlet fluid becomes heated and exists from it.

The authors obtained interesting results, which can be helpful for engineers and researchers that work on cooling of electronic devices such as LED, VLSI circuits and MEMS, as well as similar devices.

This manuscript is an original work, has not been published and is not under consideration for publication elsewhere. About the competing interests, the authors declare that they have no competing interests.

This study aims to explore the idea of solving the problem of squeezing nanofluid flow between two parallel plates using a novel mathematical method.

The unsteady squeezing flow is a coupled fourth-order boundary value problem with flow velocity and temperature as the desired unknowns. In the first step, the conditions that guarantee the existence of a unique solution are obtained. Then following Green’s function-based approach, an iterative method for solving the problem is developed.

The accuracy of the method is examined by comparing the obtained results with existing numerical data, indicating excellent agreement between the two. In addition, the effects of nanoparticle shape and volume fraction on the flow and heat transfer characteristics are addressed. The results reveal that although the nanoparticle shape strongly affects the temperature distribution in the squeezing flow, it only has a slight impact on the velocity field. Furthermore, the highest and lowest Nusselt numbers belong to the platelets and spherical nanoparticles, respectively.

A semi-analytical method with computational support is developed for solving the unsteady squeezing flow problem. Moreover, the existence and uniqueness of the solution are discussed for the first time.

The purpose of this study is to determine the impact of two-phase power law nanofluid on a curved arterial blood flow under the presence of ovelapped stenosis. Over the past couple of decades, the percentage of deaths associated with blood vessel diseases has risen sharply to nearly one third of all fatalities. For vascular disease to be stopped in its tracks, it is essential to understand the vascular geometry and blood flow within the artery. In recent scenarios, because of higher thermal properties and the ability to move across stenosis and tumor cells, nanoparticles are becoming a more common and effective approach in treating cardiovascular diseases and cancer cells.

The present mathematical study investigates the blood flow behavior in the overlapped stenosed curved artery with cylinder shape catheter. The induced magnetic field and entropy generation for blood flow in the presence of a heat source, magnetic field and nanoparticle (Fe₃O₄) have been analyzed numerically. Blood is considered in artery as two-phases: core and plasma region. Power-law fluid has been considered for core region fluid, whereas Newtonian fluid is considered in the plasma region. Strongly implicit Stone’s method has been considered to solve the system of nonlinear partial differential equations (PDE’s) with 10–6 tolerance error.

The influence of various parameters has been discussed graphically. This study concludes that arterial curvature increases the probability of atherosclerosis deposition, while using an external heating source flow temperature and entropy production. In addition, if the thermal treatment procedure is carried out inside a magnetic field, it will aid in controlling blood flow velocity.

The findings of this computational analysis hold great significance for clinical researchers and biologists, as they offer the ability to anticipate the occurrence of endothelial cell injury and plaque accumulation in curved arteries with specific wall shear stress patterns. Consequently, these insights may contribute to the potential alleviation of the severity of these illnesses. Furthermore, the application of nanoparticles and external heat sources in the discipline of blood circulation has potential in the medically healing of illness conditions such as stenosis, cancer cells and muscular discomfort through the usage of beneficial effects.